01
Alloy 59 Pickled Round Bar
Rounds below 19.05 mm descaled in acid so the surface arrives ready for fabrication.
Request Availability →Alloy 59 Round Bar
Low-iron nickel-chromium-molybdenum round bar for mixed acid duty, FGD internals and sour-service machining.
Iron Held at 1.5%
ASTM B574 caps iron at 1.5% for N06059, and we release this Alloy 59 round bar against that ceiling on every certificate.
Both Acid Families Covered
Moreover, chromium and molybdenum in this Alloy 59 round bar carry oxidising and reducing duty in one matrix.
Cooling Route Disclosed
Furthermore, we state the quench behind this Alloy 59 round bar, because a slow cool costs the corrosion margin.
PRODUCT OVERVIEW
About Alloy 59 Round Bar
Alloy 59 round bar arrives in UNS N06059, the low-iron nickel-chromium-molybdenum grade for mixed acid duty. Iron and silicon at 1.5% and 0.10% maximum hold this Alloy 59 round bar close to a clean solution.
The B574 surface split governs round bar of this grade, so pickled stock arrives below 19.05 mm while ground or turned stock arrives above it. We supply this Alloy 59 round bar to ASTM B574 and ASME SB574 in hot-worked, annealed and cold-drawn states, with the ASTM B564 forging route above 88.9 mm. Every consignment of this round bar leaves with a heat-number record, the anneal and quench route actually used and a set of EN 10204 3.1 papers.
Meanwhile, that lean matrix is what lets this Alloy 59 round bar keep its passive film through an upset. The full chemistry window and the physical data behind this Alloy 59 round bar sit on our Alloy 59 material page for cross-reference.
PRODUCT FEATURES
Key Features of Alloy 59 Round Bar
Alloy 59 round bar arrives in UNS N06059, the low-iron nickel-chromium-molybdenum grade that holds iron to 1.5% and silicon to 0.10%, so one matrix covers both acid families. We supply ASTM B574 round bar in pickled, ground and cold-drawn conditions, cut to length for mixed acid plant, flue gas desulphurisation and sour service. Every Alloy 59 round bar consignment travels with heat-number traceability, EN 10204 3.1 mill test reports and full export documentation.
Alloy 59
Iron at the Floor
For example, 1.5% iron in this Alloy 59 round bar is a quarter of the ceiling C-276 allows, which steadies the passive film.
01
Two Acid Families at Once
Specifically, chromium at 22.0–24.0% and molybdenum at 15.0–16.5% carry this Alloy 59 round bar through both families.
02
Pitting Equivalent at the Top
Moreover, the lean matrix lifts the pitting resistance equivalent of this Alloy 59 round bar to the head of the wrought nickel family.
03
Silicon and Carbon Held Low
Therefore, silicon at 0.10% and carbon at 0.010% keep the weld zone of this Alloy 59 round bar stable without a furnace pass.
04
Cold Work Sets the Strength
In addition, this Alloy 59 round bar takes nothing from aging, so drawing is the only route above the annealed floor.
05
No Hardness Figure Quoted
Besides, ASTM B574 prints no hardness ceiling for this grade, so we release this Alloy 59 round bar on chemistry and tensile results.
06
Sour Service Listed
Consequently, NACE MR0175 lists this Alloy 59 round bar at the condition the standard sets rather than at an invented figure.
07
Non-Magnetic in Service
Finally, the annealed matrix keeps this Alloy 59 round bar non-magnetic for instrument and seal work.
08
WHY CHOOSE US
Why Choose Alloy 59
The delivery surface carries more weight on an Alloy 59 round bar order than the diameter does. Besides, we settle the anneal, the descaled surface and the certificate ahead of the quote on this Alloy 59 round bar.
01
Duty Read Before Pricing
We record the medium, its concentration and its temperature for your Alloy 59 round bar before proposing a delivery state.
02
Certificates Tied to the Heat
Specifically, EN 10204 3.1 papers, heat numbers and dimensional records follow each Alloy 59 round bar consignment.
03
Welded or Machined, One Route
In addition, this Alloy 59 round bar flows through one process whether your shop welds it into a vessel or turns it on a lathe.
04
Terms Stated in Writing
Quotations for this Alloy 59 round bar name the medium, the section, the finish and the document set rather than leaving them open.
MANUFACTURING PROCESS
Reliable Production For Critical Applications
Bar production for Alloy 59 round bar runs from charge balancing through to final packing. We log each stage of this Alloy 59 round bar route against its own heat number.
01
Charge Weighing
We charge nickel, chromium and molybdenum to the B574 window before this Alloy 59 round bar is melted.
02
Melting and Refining
First, the charge for this Alloy 59 round bar melts and refines under AOD practice that holds carbon and silicon low.
03
Hot Reduction
Next, forging and rolling reduce the ingot to this Alloy 59 round bar section between 1180 °C and 950 °C.
04
Solution Annealing
Then, we hold this Alloy 59 round bar between 1100 °C and 1180 °C.
05
Water Quenching
After that, this Alloy 59 round bar drops into the tank, because the fall to 500 °C has to beat 150 °C per minute.
06
Pickling and Descale
We then strip the mill scale and leave this Alloy 59 round bar ready for fabrication.
07
Cold Finishing
Subsequently, drawing, turning or grinding brings this Alloy 59 round bar to the ordered size and finish.
08
Testing and Release
Finally, chemistry, tensile and dimensional checks clear this Alloy 59 round bar for dispatch.
Manufacturing Facility
MANUFACTURING CAPABILITY
Advanced Production For Nickel Alloy Products
Stock lengths and made-to-order heats of Alloy 59 round bar leave on one production schedule. Moreover, we quote this Alloy 59 round bar inside our bar and rod program.
20,000+ m²
Factory Area
Hot working, annealing, quenching and finishing lines for Alloy 59 round bar share one site.
50+
Production Machines
Units covering hot working, annealing, quenching and grinding for this Alloy 59 round bar.
600 Tons
Monthly Capacity
Alloy 59 round bar output across stock and bespoke lots.
30+
Technical Engineers
Metallurgists who set the anneal and quench plan for this Alloy 59 round bar against your duty.
30+ Countries
Export Reach
In addition, sealed export packing carries this Alloy 59 round bar to buyers on five continents.
QUALITY ASSURANCE
Strict Quality Control From Production To Delivery
Release waits on the heat behind your Alloy 59 round bar clearing our ISO 9001 route. Moreover, the chemistry, tensile and surface checks on this Alloy 59 round bar follow the requirements the order names.
01
Heat Identification
We check the grade and heat number on this Alloy 59 round bar against your purchase order before anything ships.
02
Chemistry Verification
Specifically, iron, silicon and carbon in this Alloy 59 round bar go against the B574 table for your lot.
03
Tensile Verification
In addition, every heat of this Alloy 59 round bar carries reported tensile and yield values measured against the B574 floor.
04
Quench Record Referenced
Every consignment of this Alloy 59 round bar ships with EN 10204 3.1 papers and the cooling record keyed to its heat.
PRODUCT FORMS
Available Product Forms
We quote the variants below for Alloy 59 round bar against the drawing rather than from a catalogue. In addition, the list shows the deliveries ordered most often for this Alloy 59 round bar.
02
Alloy 59 Ground Round Bar
Larger rounds ground into a close diameter band instead of pickled.
Request Availability →
03
Alloy 59 Turned Round Bar
Rounds carrying a machined skin at an even diameter for further turning.
Request Availability →
04
Alloy 59 Cold-Drawn Round Bar
Drawn rounds with proof stress well above the annealed floor.
Request Availability →
05
Alloy 59 Custom Round Bar
Diameters, lengths and delivery states produced against your drawing.
Request Availability →
APPLICATIONS
Engineered For Demanding Industries
Alloy 59 round bar suits plant where the process moves between oxidising and reducing steps. In addition, the list below shows where this Alloy 59 round bar serves.
Discuss Your Application →
01
Alloy 59 Scrubber Agitator Shafts
Shaft stock for absorbers where the slurry turns acidic between process steps.
02
Alloy 59 Acid Cooler Tube Plugs
Plugs and ferrules machined for exchangers that cool hot concentrated acid.
03
Alloy 59 Brine Circulation Pump Shafts
Shafting for pumps moving chlorinated brine through cooling circuits.
04
Alloy 59 Sour Service Valve Stems
Stems and seats machined for equipment qualified to the sour-service standard.
05
Alloy 59 Reactor Agitator Shafts
Shafts for vessels that alternate between oxidising and reducing chemistry.
06
Alloy 59 Bleach Plant Digester Fittings
Machined fittings for pulp towers that meet chlorine dioxide.
07
Alloy 59 Incinerator Quench Nozzles
Nozzle bodies exposed to acid condensate in off-gas quench sections.
08
Alloy 59 Pharmaceutical Reactor Baffles
Baffle and support hardware that survives alternating acid and alkali cleaning.
TECHNICAL INFORMATION
Technical Specifications
Detailed technical information including chemical composition, mechanical properties, standards and available dimensions.
Chemical Composition
ASTM B574 fixes the UNS N06059 window that governs this round bar, holding iron to 1.5% maximum and capping silicon at 0.10%. In addition, chromium runs between 22.0% and 24.0% in this round bar, while molybdenum sits between 15.0% and 16.5%.
Meanwhile, the full composition table on the Alloy 59 material page sets every element against its ASTM B574 limit for this round bar.
Mechanical Properties
The floors in the table below come from the ASTM B574 bar table for UNS N06059. Therefore, the ordered condition and the ruling section settle final acceptance of Alloy 59 round bar.
| Condition and Grade | Tensile Strength, min. | Yield Strength (0.2%), min. | Elongation, min. |
|---|---|---|---|
| Solution Annealed — UNS N06059 | ≥690 MPa (100 ksi) | ≥310 MPa (45 ksi) | 45% |
- ASTM B574 carries three columns in Table 5 and prints no hardness requirement against N06059, so release rests on chemistry and tensile results rather than on an indenter reading. Besides, the title of that document limits it to rod and bar, and clause 1.2 stops the bar route at 88.9 mm. Therefore, work above that diameter moves onto the ASTM B564 forging route, where we agree the test position instead of assuming it.
Physical Properties
Published references place the density of this round bar near 8.6 g/cm³ and its melting range at 1310–1360 °C. Moreover, an elastic modulus close to 210 GPa and a relative permeability of 1.001 maximum keep this round bar effectively non-magnetic in service.
Therefore, the physical properties table on the Alloy 59 material page carries the conductivity, the resistivity and the remaining design values behind this round bar.
Heat Treatment
The water quench is the step that defines this Alloy 59 round bar, because the section has to fall from the anneal to about 500 °C faster than 150 °C per minute. Moreover, a section deformed beyond 15% returns to that anneal before it enters service.
| Condition | Typical Treatment |
|---|---|
| Solution Annealed | Held between 1100 °C and 1180 °C and water quenched, with about 1120 °C the preferred figure |
| Cooling Rate | Better than 150 °C per minute from the anneal down to about 500 °C, or grain-boundary phases form |
| Hot-Worked | Forged or rolled between 1180 °C and 950 °C, with heavy reduction taken at the top of that band |
| Cold-Drawn | Drawn after the anneal, in one of the three graded strength levels that Table 3 defines |
| Cold-Forming Limit | Deformation beyond 15% sends the section back through the final solution anneal before service |
| Stress-Relief Caution | A relief pass inside the precipitation band still costs corrosion resistance, so the alternative is settled before it is booked |
| Post-Weld Anneal | Most joints enter service as welded, because the low carbon and silicon levels keep the weld zone stable |
Standards
ASTM B574 is the principal UNS N06059 rod and bar document for this round bar, issued by ASTM International. Moreover, ASME SB574 covers pressure equipment built from this round bar while ASTM B564 takes over above 88.9 mm.
| Standard | Product or Application |
|---|---|
| ASTM B574 / ASME SB574 | Nickel-chromium-molybdenum rod and bar, solution annealed |
| ASTM B564 / ASME SB564 | Forgings and forging stock above the bar window |
| NACE MR0175 / ISO 15156 | Sour service, listed at the highest test level |
Beyond that, the standards table on the Alloy 59 material page carries the European designations, the tubular documents and the flat-product call-outs for this round bar.
Dimensions
The table below lists the Alloy 59 round bar sizes we ship most often, while the route, the document and the lot size decide what else is possible. Please confirm your own size, section and length with the inquiry.
| Product Form | Typical Supply | Length |
|---|---|---|
| Round Bar | 7.94–88.9 mm dia., solution annealed to ASTM B574 | Cut to length or random |
| Pickled Round Bar | 7.94–19.05 mm dia., clause 1.2.1 | Cut to length or random |
| Ground Round Bar | 19.05–88.9 mm dia., clause 1.2.2 | Cut to length |
| Turned Round Bar | 19.05–88.9 mm dia., machined skin | Cut to length |
| Cold-Drawn Round Bar | 6.35–88.9 mm dia., clause 1.2.3 | Cut to length |
| Custom Round Bar | To drawing | Custom |
ASTM B574 splits this grade by delivery surface rather than by grade, so stock below 19.05 mm arrives pickled while the larger band arrives ground or turned. In addition, tell us the finished diameter and the surface your shop expects.
Surface Finishes
For this round bar, the finish decides how the part feeds, seals and resists attack. Therefore, we fix the surface condition on this Alloy 59 round bar when the order opens.
| Surface Condition | Typical Use |
|---|---|
| Solution Annealed and Pickled | The anneal followed by acid descaling leaves this round bar scale-free for mixed acid and chloride duty. |
| Peeled | A machined skin gives this round bar an even diameter ahead of the finishing cut. |
| Cold Drawn | Drawn stock holds a close diameter on this round bar while the drawing pass lifts proof stress. |
In contrast, the surface finishes table on the Alloy 59 material page lists the further conditions we can quote for this round bar.
Related forms from the same heat cover Alloy 59 Threaded Rod, Alloy 59 Welding Wire and Alloy 59 Centreless-Ground Rod when your round bar order needs them.
TECHNICAL DOCUMENTATION
Download Technical Datasheet
Get detailed information including specifications, standards, dimensions and material properties.
HOW TO START
Start Your Order in 6 Simple Steps
One coordinator carries your Alloy 59 round bar enquiry from the first question through to loading. In addition, stock of this Alloy 59 round bar leaves inside fifteen days, and a freshly annealed heat runs about twenty-five.
1
Give Us the Duty
Send the medium, its concentration and its temperature together with the size, quantity and standard this Alloy 59 round bar faces.
2
Settle the State
We then fix the anneal cycle, the delivery condition and the tolerance band on this Alloy 59 round bar.
3
Read the Offer
Pricing for this Alloy 59 round bar arrives by size, quantity and destination port.
4
Sign off the Order
You confirm the specification, the terms and the schedule for this Alloy 59 round bar in writing.
5
Book the Witness Points
Then we schedule any third-party inspection or dimensional review of this Alloy 59 round bar before production starts.
6
Ship and Document
This Alloy 59 round bar arrives with mill papers, a packing list and the certificate set.
CERTIFICATIONS & QUALITY DOCUMENTATION
Certifications & Quality Documentation
Our production and inspection processes are certified to international standards, and every delivery ships with EN 10204 3.1 mill test certificates.
ISO 9001:2015
Quality Management System
PED 2014/68/EU
Pressure Equipment Directive
ASTM / ASME
Material Standards Compliance
EN 10204 3.1
Mill Test Certificates
FAQ
Frequently Asked Questions
Which standard covers this Alloy 59 round bar?
ASTM B574 and ASME SB574 cover this Alloy 59 round bar, and clause 1.2 stops the bar route at 88.9 mm.
Does this Alloy 59 round bar qualify for sour service?
Yes. NACE MR0175 lists this grade at the condition that document sets, and we document that condition per heat.
Which filler metal suits this Alloy 59 round bar?
ERNiCrMo-13 bare wire to AWS A5.14 joins this Alloy 59 round bar, with ENiCrMo-13 covered electrodes to AWS A5.11 for manual work.
Why does this Alloy 59 round bar ship water quenched?
Iron and silicon sit so low that a slow cool lets grain-boundary phases form, so every heat leaves the anneal straight into the tank.
Does a weld in this Alloy 59 round bar need a post-weld anneal?
Usually not. Low carbon and low silicon leave most joints serviceable as welded.
How high can this Alloy 59 round bar run in continuous service?
Published design data covers this Alloy 59 round bar from about −196 °C upward, and we confirm the ceiling against your design code before the order.
What is your MOQ for this Alloy 59 round bar?
Trial lengths of this Alloy 59 round bar are welcome, and one piece covers most stock sizes.
What are your trade terms for this Alloy 59 round bar?
Trade terms for this Alloy 59 round bar open on FOB, and EXW, CIF or DAP follow once we know the destination port.
What is the lead time for this Alloy 59 round bar?
Stock sizes of this Alloy 59 round bar ship in 7 to 15 days, while a made-to-order annealed heat needs about 25 days.
Do you provide EN 10204 3.1 or 3.2 certificates for this Alloy 59 round bar?
EN 10204 3.1 papers cover every heat of this Alloy 59 round bar, and a 3.2 endorsement can be arranged.
REQUEST FOR QUOTATION
Need A Custom Alloy Solution?
Our Alloy 59 round bar offer names the diameter, the delivery surface and the annealed state against ASTM B574. Send the medium, the size band and your quantity so we can price this Alloy 59 round bar.
We take your Alloy 59 round bar inquiry through the anneal, the finish and the document scope before the price goes out. Production follows the signed sheet, and the full paper set travels with this Alloy 59 round bar.
