01
Monel 400 Annealed Monel Wire
Soft annealed wire that weaves, knits and heads without cracking.
Request Availability →Monel 400 Wire
Monel 400 wire from 0.10 to 10 mm in four tempers for demister pads, marine mesh and cold-headed rivets.
Seawater and HF Duty Stock
We hold this Monel 400 wire for alkylation, marine and brine work where 300-series stainless pits or cracks.
Strength from Cold Work Alone
Specifically, this Monel 400 wire cannot be age hardened, so a heavier drawing pass rather than a heat treatment raises its yield.
Documents Matched to the Order
Moreover, the mill certificate, hardness records and export papers for this Monel 400 wire reach you as one set.
PRODUCT OVERVIEW
About Monel 400 Wire
Monel 400 wire arrives in UNS N04400, the solid-solution nickel-copper alloy holding nickel at 63% and above. Flowing seawater, hydrofluoric acid and strong alkali leave this Monel 400 wire intact where stainless grades pit or crack.
We supply Monel 400 wire to ASTM B164 and ASME SB164 in hot-worked, annealed, stress-relieved and cold-drawn conditions. Your order for this Monel 400 wire carries heat-number records and EN 10204 3.1 paperwork for goods-in checks. Besides, diameter, condition and finish on the wire are agreed before the heat is booked.
Meanwhile, the chemistry and the design values behind Monel 400 wire sit on our Monel 400 material page for cross-reference.
PRODUCT FEATURES
Key Features of Monel 400 Wire
Monel 400 wire arrives in UNS N04400, the solid-solution nickel-copper alloy that holds nickel at 63% and above. We provide ASTM B164 and ASME SB164 wire from 0.10 to 10 mm in annealed, quarter-hard, half-hard and spring tempers for marine yards, alkylation units and brine plant. Every Monel 400 wire order carries heat-number traceability, EN 10204 3.1 mill test reports and full export documentation.
Monel 400
Four Temper Steps
For example, this Monel 400 wire ships annealed, quarter hard, half hard or spring temper.
01
Fine Diameter Capability
Specifically, this Monel 400 wire draws down to fine sizes for weaving and filtration.
02
Seawater Resistance
In addition, this Monel 400 wire keeps a clean surface in flowing seawater and salt spray.
03
Acid and Alkali Cover
Moreover, this Monel 400 wire resists hydrofluoric acid and strong alkali across the concentration range.
04
Cold-Forming Ductility
Annealed this Monel 400 wire heads, bends and knits without cracking.
05
Spring-Temper Strength
Heavily reduced this Monel 400 wire reaches 1000 MPa and above for springs and clips.
06
Consistent Coiling
We wind this Monel 400 wire with controlled layering so feeders run without tangling.
07
Full Traceability
Every coil of this Monel 400 wire carries heat numbers and EN 10204 3.1 documents.
08
WHY CHOOSE US
Why Choose Monel 400
Mesh and cold-headed parts ask for temper control first in Monel 400 wire. Specifically, we fix the diameter, temper and coil weight of this Monel 400 wire before we quote it.
01
Duty Read Before Pricing
We record the seawater, acid or alkali conditions your Monel 400 wire will meet before proposing a delivery condition.
02
Certificates Tied to the Heat
Specifically, EN 10204 3.1 papers, heat numbers and PMI records follow each Monel 400 wire delivery.
03
Trial Pieces and Container Lots
In addition, this Monel 400 wire moves through one route whether you need a single length or a full container.
04
Terms Stated in Writing
Quotations for this Monel 400 wire name the condition, section, finish and document set instead of leaving them open.
MANUFACTURING PROCESS
Reliable Production For Critical Applications
Wire production for Monel 400 wire runs from charge weighing to final spooling. We log every stage of this Monel 400 wire route against its heat number.
01
Charge Weighing
We weigh refined nickel and cathode copper so this Monel 400 wire melts inside the N04400 window.
02
Melting and Casting
First, the charge for this Monel 400 wire melts and casts into electrode stock.
03
Hot Rolling to Rod
Next, hot rolling reduces cast stock into drawing rod for this Monel 400 wire.
04
Annealing and Descaling
Then, we anneal and descale the rod before this Monel 400 wire enters the draw bench.
05
Wire Drawing
After that, successive dies pull this Monel 400 wire down to the ordered diameter.
06
Intermediate Anneals
Because this Monel 400 wire work-hardens quickly, we soften it between drawing passes.
07
Final Temper
Subsequently, the last reduction sets this Monel 400 wire to the ordered temper.
08
Coiling and Release
Finally, we wind this Monel 400 wire onto coils and spools and clear the heat for dispatch.
Manufacturing Facility
MANUFACTURING CAPABILITY
Advanced Production For Nickel Alloy Products
Stock lengths and made-to-order lots of Monel 400 wire leave on one schedule. Moreover, we confirm section and finish of this Monel 400 wire before release. Besides, this Monel 400 wire sits inside our Monel 400 bar and rod program.
20,000+ m²
Factory Area
Specifically, melting, forging, drawing and inspection halls serve Monel 400 wire under one roof.
50+
Production Machines
Equipment covering hot working, annealing and cold finishing for this Monel 400 wire.
600 Tons
Monthly Capacity
Monel 400 wire output across stock and made-to-order sizes.
30+
Technical Engineers
Metallurgists who set the condition and document scope of this Monel 400 wire against your duty.
30+ Countries
Export Reach
In addition, documented logistics carry this Monel 400 wire worldwide.
QUALITY ASSURANCE
Strict Quality Control From Production To Delivery
No Monel 400 wire leaves the yard before its heat has cleared our ISO 9001 inspection route. In addition, we check this Monel 400 wire against the chemistry, mechanical properties, dimensions and surface the order names.
01
Heat Identification
We confirm the grade and heat number of this Monel 400 wire against your purchase order.
02
Dimensional Verification
Specifically, the size, length and straightness of this Monel 400 wire go against standard and drawing tolerances.
03
Property Testing
In addition, tensile, hardness and NDT checks run wherever your Monel 400 wire specification requires them.
04
Certificate Assembly
Every consignment of this Monel 400 wire carries EN 10204 3.1 documents keyed to the heat number.
PRODUCT FORMS
Available Product Forms
Conditions and variants of Monel 400 wire cover different machining and service needs. In addition, the list below sets out the Monel 400 Wire variants we quote most often.
02
Monel 400 Quarter-Hard Wire
Wire drawn to an intermediate temper for cold heading and forming.
Request Availability →
03
Monel 400 Half-Hard Wire
Drawn wire with higher delivered strength for pins and clips.
Request Availability →
04
Monel 400 Spring-Temper Wire
Heavily reduced wire that holds a set in springs and snap rings.
Request Availability →
05
Monel 400 Fine Monel Wire
Fine wire for weaving and filtration media.
Request Availability →
06
Monel 400 Straightened and Cut Wire
Wire straightened and cut for cold-forming blanks.
Request Availability →
07
Monel 400 Wire Rod
Rod stock feeding downstream redraw lines.
Request Availability →
08
Monel 400 Custom Wire
Custom diameters, tempers and packing produced to your callout.
Request Availability →
APPLICATIONS
Engineered For Demanding Industries
Monel 400 wire is chosen where corrosion resistance meets woven or formed geometry. Consequently, the applications below show where this Monel 400 wire serves.
Discuss Your Application →
01
Monel 400 Knitted Demister Pads
Wire knitted into pads that strip mist from gas streams.
02
Monel 400 Woven Marine Mesh
Wire woven into screens for seawater and brine filtration.
03
Monel 400 Cold-Headed Rivets
Wire headed into rivets and screws for hull and deck work.
04
Monel 400 Spring Clips and Rings
Springs and retaining rings that must hold force in salt air.
05
Monel 400 Lock Wire
Wire used to lock fasteners on marine and process equipment.
06
Monel 400 Anode and Cathode Mesh
Mesh current collectors inside electrochemical plant.
07
Monel 400 Welding Consumable Core
Wire feeding downstream filler-metal production.
08
Monel 400 Filtration Media
Filter elements for seawater and acid process streams.
TECHNICAL INFORMATION
Technical Specifications
Detailed technical information including chemical composition, mechanical properties, standards and available dimensions.
Chemical Composition
UNS N04400 carries nickel as its balance and holds copper inside a 28.0% to 34.0% window, so every heat record for this wire prints a copper figure rather than a grade name. Besides, that window is what keeps the seawater and acid behaviour of this wire repeatable from heat to heat.
For the full element-by-element limit set, open the composition breakdown held on the Monel 400 material page for this wire.
Mechanical Properties
Typical room-temperature ranges for UNS N04400 wire appear below, taken from published alloy references and aligned with the temper notation of ASTM B164 Table 2. Therefore the ordered temper and diameter decide the acceptance values for Monel 400 wire.
| Temper | Tensile Strength, typical | Yield Strength, typical | Elongation, typical |
|---|---|---|---|
| Annealed (soft) | 480–600 MPa (70–85 ksi) | 170–250 MPa (25–36 ksi) | 35–50% |
| Quarter hard | 600–750 MPa (85–110 ksi) | 380 MPa (55 ksi) min. | 20–30% |
| Half hard | 750–900 MPa (110–130 ksi) | 480 MPa (70 ksi) min. | 10–20% |
| Full hard (spring) | 1000–1200 MPa (145–175 ksi) | 690 MPa (100 ksi) min. | 2–5% |
- ASTM B164 covers cold-worked wire in Table 2, so the ordered temper and diameter govern the acceptance values rather than the typical ranges above.
Physical Properties
Published references place this wire at a density near 8.80 g/cm³ with a melting range of 1300–1350 °C. In addition, the Curie range sits just above ambient, so a wire behaves as a weakly magnetic material near room temperature.
Meanwhile, the physical properties table on the Monel 400 material page holds the thermal conductivity, the electrical resistivity and the remaining design values behind this wire.
Delivery Conditions
Monel 400 wire ships in the delivery states below. Specifically, wire rod supplies drawing stock while the drawn tempers are finished product wire.
| Delivery State | Typical Diameter | Notes |
|---|---|---|
| Hot rolled wire rod | 5.5–8.0 mm | Drawing stock supplied for downstream redraw |
| Annealed | 0.10–10 mm | Softest product wire, offering the best ductility |
| Quarter hard | 0.20–8.0 mm | Intermediate temper for heading and forming |
| Half hard | 0.20–6.0 mm | Higher strength for pins, clips and meshes |
| Spring temper | 0.20–6.0 mm | Heaviest reduction, for springs and retaining rings |
Delivery note: Monel 400 work-hardens quickly, so the wire route carries intermediate anneals and ships to ASTM B164 Table 2 in the ordered temper.
Standards
ASTM B164 reaches cold-worked wire through its Table 2, so this wire is quoted to that table alongside DIN 17753 and ISO 9724. Moreover, AMS 4730 covers wire of this wire and AMS 4731 covers its wire and ribbon forms.
| Standard | Product or Application |
|---|---|
| ASTM B164 Table 2 | Cold-worked wire, UNS N04400 |
| AMS 4730 | Wire for aerospace and defence programmes |
| DIN 17753 / ISO 9724 | European and ISO wire documents |
Finally, the full standards list on the Monel 400 material page adds the European designations, the defence documents and the fastener specifications behind this wire.
Dimensions
Dimensions of Monel 400 wire follow the manufacturing route, the standard and the order quantity. Therefore, the table below lists typical supply ranges, so please confirm your size in the inquiry.
| Product Form | Typical Supply | Length |
|---|---|---|
| Wire (Coil / Spool) | 0.10–10 mm dia., typical | Coil, spool or custom |
| Wire Rod (Drawing Stock) | 5.5–8.0 mm dia. | Coil |
| Fine Wire | 0.10–0.80 mm dia. | Spool |
| Straightened and Cut Wire | 1.0–10 mm dia. | Straight lengths |
| Spring-Temper Wire | 0.20–6.0 mm dia. | Coil or spool |
| Custom Wire | To drawing | Custom |
Available sizes of this Monel 400 wire depend on the manufacturing route, the standard, the material condition and the order quantity. Please confirm your required wire size, section and length in the inquiry.
Surface Finishes
Finish decides what the next operation does to this material, whether that is a turning pass, a grinding pass or a welding cell. Specifically, we agree the finish on this Monel 400 wire before we release the order.
| Surface Condition | Typical Use |
|---|---|
| Bright Annealed | Protective-atmosphere annealing leaves this wire oxide-free and ready to draw. |
| Pickled | Acid cleaning descaled this wire after the anneal. |
| Coated | A light carrier film on this wire that protects it during downstream redrawing. |
Meanwhile, the surface finishes table on the Monel 400 material page lists the remaining conditions we quote for this wire.
Related forms from the same heat cover Monel 400 Bright Bar, Monel 400 Centreless-Ground Rod and Monel 400 Cold-Drawn Bar when your wire order needs them.
TECHNICAL DOCUMENTATION
Download Technical Datasheet
Get detailed information including specifications, standards, dimensions and material properties.
HOW TO START
Start Your Order in 6 Simple Steps
One coordinator carries your Monel 400 wire order from first question to loading. Therefore, most orders for this Monel 400 wire move from quotation to dispatch inside three weeks.
1
Send the Duty Data
Give the size, quantity, standard and the seawater or acid duty your Monel 400 wire will see.
2
Fix the Condition
Then we set the delivery condition and tolerance for this Monel 400 wire.
3
Review the Offer
Receive pricing for this Monel 400 wire by dimension, quantity and destination port.
4
Approve the Order
Approve the specification, terms and schedule for this Monel 400 wire in writing.
5
Witness Points Agreed
Any third-party inspection of this Monel 400 wire is booked before production starts.
6
Dispatch and Documents
Receive this Monel 400 wire with the mill certificate, packing list and shipping papers.
CERTIFICATIONS & QUALITY DOCUMENTATION
Certifications & Quality Documentation
Our production and inspection processes are certified to international standards, and every delivery ships with EN 10204 3.1 mill test certificates.
ISO 9001:2015
Quality Management System
PED 2014/68/EU
Pressure Equipment Directive
ASTM / ASME
Material Standards Compliance
EN 10204 3.1
Mill Test Certificates
FAQ
Frequently Asked Questions
Which specification covers this Monel 400 wire?
ASTM B164 reaches cold-worked wire through its Table 2, and AMS 4730, DIN 17753 and ISO 9724 cover this Monel 400 wire as well.
What diameters does this Monel 400 wire span?
Product wire of this Monel 400 wire typically runs from 0.10 to 10 mm, while drawing stock spans 5.5 to 8.0 mm.
Which tempers are available for this Monel 400 wire?
This wire ships annealed, quarter hard, half hard or spring temper, with finer steps quoted by diameter.
Does the wire strength of this Monel 400 wire hold after straightening?
No. Cold-worked values for this Monel 400 wire lapse once it is straightened and cut, so order the temper your parts need.
How is the price of this Monel 400 wire calculated?
Pricing follows weight for this Monel 400 wire, with the prevailing nickel and copper quotations applied on the order date.
What is your MOQ for this Monel 400 wire?
One spool covers many common diameters of this Monel 400 wire.
What are your trade terms for this Monel 400 wire?
FOB covers most orders for this Monel 400 wire, and EXW or CIF terms are available when you ask.
What is the lead time for this Monel 400 wire?
Stock sizes of this Monel 400 wire dispatch in 7 to 15 days, while custom drawing takes longer.
Do you provide EN 10204 3.1 or 3.2 certificates for this Monel 400 wire?
Yes. Every coil of this Monel 400 wire ships with 3.1, and a 3.2 endorsement is booked through the order.
What information should an enquiry for this Monel 400 wire include?
Please send the diameter, temper, coil weight, standard and destination so we can quote this Monel 400 wire accurately.
REQUEST FOR QUOTATION
Need A Custom Alloy Solution?
Monel 400 wire is quoted by diameter, temper and coil weight to ASTM B164 Table 2. Send those figures with your quantity so we can price this Monel 400 wire.
Specifically, we review your Monel 400 wire specification, confirm the condition and document scope, and return pricing with clear terms. Production then follows the signed specification, and each consignment of this Monel 400 wire ships with the full paperwork set.
