01
Monel 400 Metric Threaded Rod
Rod rolled to metric coarse and fine threads through M64.
Request Availability →Monel 400 Threaded Rod
Monel 400 fully threaded rod to ASTM B164 for marine flange bolting, deck anchoring and HF unit assemblies.
Seawater and HF Duty Stock
We hold this Monel 400 threaded rod for alkylation, marine and brine work where 300-series stainless pits or cracks.
Strength from Cold Work Alone
Specifically, this Monel 400 threaded rod cannot be age hardened, so a heavier drawing pass rather than a heat treatment raises its yield.
Documents Matched to the Order
Moreover, the mill certificate, hardness records and export papers for this Monel 400 threaded rod reach you as one set.
PRODUCT OVERVIEW
About Monel 400 Threaded Rod
Monel 400 threaded rod arrives in UNS N04400, the solid-solution nickel-copper alloy holding nickel at 63% and above. Flowing seawater, hydrofluoric acid and strong alkali leave this Monel 400 threaded rod intact where stainless grades pit or crack.
We supply Monel 400 threaded rod to ASTM B164 and ASME SB164 in hot-worked, annealed, stress-relieved and cold-drawn conditions. Your order for this Monel 400 threaded rod carries heat-number records and EN 10204 3.1 paperwork for goods-in checks. Besides, diameter, condition and finish on the threaded rod are agreed before the heat is booked.
Meanwhile, the chemistry and the design values behind Monel 400 threaded rod sit on our Monel 400 material page for cross-reference.
PRODUCT FEATURES
Key Features of Monel 400 Threaded Rod
Monel 400 threaded rod arrives in UNS N04400, the solid-solution nickel-copper alloy that holds nickel at 63% and above. We provide ASTM B164 and ASME SB164 threaded rod fully threaded in the annealed and stress-relieved conditions for marine yards, alkylation units and brine plant. Every Monel 400 threaded rod order carries heat-number traceability, EN 10204 3.1 mill test reports and full export documentation.
Monel 400
Flowing-Seawater Resistance
For example, this Monel 400 threaded rod keeps a clean surface in moving seawater, where 300-series stainless pits within a few seasons.
01
Stagnant-Seawater Caution
However, crevices and silt traps under static conditions attack this Monel 400 threaded rod, so design drain-and-flush paths.
02
Hydrofluoric-Acid Capability
Besides, this Monel 400 threaded rod handles hydrofluoric acid across all concentrations, a niche few stainless or nickel grades share.
03
Alkali and Salt Duty
In turn, strong caustic and acid-salt streams suit this Monel 400 threaded rod, so brine hardware holds tolerance longer.
04
Strength from Cold Work
Cold drawing lifts the yield of this Monel 400 threaded rod from the 25 ksi annealed floor toward 85 ksi in light sections.
05
No Age Hardening
Specifically, this Monel 400 threaded rod cannot be precipitation hardened, so cold work sets the strength ceiling.
06
Cryogenic Ductility
Moreover, impact strength in this Monel 400 threaded rod stays flat through sub-zero and cryogenic plant.
07
Welding Without Post-Weld Anneal
Finally, ERNiCu-7 filler joins this Monel 400 threaded rod with no post-weld heat treatment.
08
WHY CHOOSE US
Why Choose Monel 400
Stud work fixes the thread form before anything else in Monel 400 threaded rod. Therefore, we agree the thread class, length and hardness of this Monel 400 threaded rod before quoting.
01
Duty Read Before Pricing
We record the seawater, acid or alkali conditions your Monel 400 threaded rod will meet before proposing a delivery condition.
02
Certificates Tied to the Heat
Specifically, EN 10204 3.1 papers, heat numbers and PMI records follow each Monel 400 threaded rod delivery.
03
Trial Pieces and Container Lots
In addition, this Monel 400 threaded rod moves through one route whether you need a single length or a full container.
04
Terms Stated in Writing
Quotations for this Monel 400 threaded rod name the condition, section, finish and document set instead of leaving them open.
MANUFACTURING PROCESS
Reliable Production For Critical Applications
Bar production for Monel 400 threaded rod runs from charge weighing to final packing. Our team logs each stage of this Monel 400 threaded rod route against its heat number.
01
Charge Weighing
We start from refined nickel and cathode copper and hold this Monel 400 threaded rod to the B164 analysis.
02
Melting and Refining
First, the charge for this Monel 400 threaded rod melts and refines under controlled practice.
03
Ingot Casting
Next, this Monel 400 threaded rod casts into ingots under controlled solidification.
04
Hot Reduction
Then, forging and rolling reduce the ingot to this Monel 400 threaded rod section.
05
Skin Removal
After that, peeling and grinding strip surface defects from this Monel 400 threaded rod.
06
Condition Heat Treatment
Subsequently, annealing or stress relief sets the ordered condition of this Monel 400 threaded rod.
07
Cold Finishing
We then draw, turn or grind this Monel 400 threaded rod to the ordered size and finish.
08
Testing and Release
Finally, chemistry, tensile and dimensional checks clear this Monel 400 threaded rod for dispatch.
Manufacturing Facility
MANUFACTURING CAPABILITY
Advanced Production For Nickel Alloy Products
Stock lengths and made-to-order lots of Monel 400 threaded rod leave on one schedule. Moreover, we confirm section and finish of this Monel 400 threaded rod before release. Besides, this Monel 400 threaded rod sits inside our Monel 400 bar and rod program.
20,000+ m²
Factory Area
Specifically, melting, forging, drawing and inspection halls serve Monel 400 threaded rod under one roof.
50+
Production Machines
Equipment covering hot working, annealing and cold finishing for this Monel 400 threaded rod.
600 Tons
Monthly Capacity
Monel 400 threaded rod output across stock and made-to-order sizes.
30+
Technical Engineers
Metallurgists who set the condition and document scope of this Monel 400 threaded rod against your duty.
30+ Countries
Export Reach
In addition, documented logistics carry this Monel 400 threaded rod worldwide.
QUALITY ASSURANCE
Strict Quality Control From Production To Delivery
No Monel 400 threaded rod leaves the yard before its heat has cleared our ISO 9001 inspection route. In addition, we check this Monel 400 threaded rod against the chemistry, mechanical properties, dimensions and surface the order names.
01
Heat Identification
We confirm the grade and heat number of this Monel 400 threaded rod against your purchase order.
02
Dimensional Verification
Specifically, the size, length and straightness of this Monel 400 threaded rod go against standard and drawing tolerances.
03
Property Testing
In addition, tensile, hardness and NDT checks run wherever your Monel 400 threaded rod specification requires them.
04
Certificate Assembly
Every consignment of this Monel 400 threaded rod carries EN 10204 3.1 documents keyed to the heat number.
PRODUCT FORMS
Available Product Forms
Conditions and variants of Monel 400 threaded rod cover different machining and service needs. In addition, the list below sets out the Monel 400 Threaded Rod variants we quote most often.
02
Monel 400 UNC Threaded Rod
Unified coarse and fine threads rolled on annealed bar.
Request Availability →
03
Monel 400 Full-Thread Studs
Studs cut and threaded to your stated length.
Request Availability →
04
Monel 400 Double-Ended Studs
Studs threaded at both ends for flanged joints.
Request Availability →
05
Monel 400 Custom Threaded Rod
Custom thread forms and lengths produced to your drawing.
Request Availability →
APPLICATIONS
Engineered For Demanding Industries
Monel 400 threaded rod is chosen where seawater, hydrofluoric acid or strong alkali decides component life. In addition, the applications below show where this Monel 400 threaded rod serves.
Discuss Your Application →
01
Monel 400 Marine Flange Bolting
Studs clamping flanged joints on seawater and brine lines.
02
Monel 400 Deck and Dock Anchors
Anchors holding equipment down in salt-laden environments.
03
Monel 400 HF Unit Fasteners
Bolting inside hydrofluoric acid alkylation units.
04
Monel 400 Pump Foundation Bolts
Foundation fasteners for seawater and chemical pumps.
05
Monel 400 Tank Support Rods
Rods suspending and steadying tank internals.
06
Monel 400 Heat-Exchanger Tie Rods
Rods holding tube bundles and baffles together.
07
Monel 400 Column Base Ties
Tie rods fixing columns and structures on site.
08
Monel 400 Custom Fastening
Cut-to-length threaded rod for bespoke assemblies.
TECHNICAL INFORMATION
Technical Specifications
Detailed technical information including chemical composition, mechanical properties, standards and available dimensions.
Chemical Composition
UNS N04400 carries nickel as its balance and holds copper inside a 28.0% to 34.0% window, so every heat record for this threaded rod prints a copper figure rather than a grade name. Besides, that window is what keeps the seawater and acid behaviour of this threaded rod repeatable from heat to heat.
For the full element-by-element limit set, open the composition breakdown held on the Monel 400 material page for this threaded rod.
Mechanical Properties
The minimum room-temperature values below apply to UNS N04400 bar in the hot-worked, annealed, stress-relieved and cold-worked conditions per ASTM B164. Consequently, condition and section size govern final acceptance of Monel 400 threaded rod.
| Condition and Section | Tensile Strength, min. | Yield Strength (0.2%), min. | Elongation, min. |
|---|---|---|---|
| Hot-worked, rounds to 305 mm (12 in.) | ≥80 ksi (552 MPa) | ≥40 ksi (276 MPa) | 30% |
| Hot-worked, annealed, all sizes | ≥70 ksi (480 MPa) | ≥25 ksi (170 MPa) | 35% |
| Cold-worked, stress-relieved, rounds 12.7–88.9 mm (1/2–3-1/2 in.) | ≥87 ksi (600 MPa) | ≥60 ksi (415 MPa) | 20% |
| Cold-worked, as-worked, rounds under 12.7 mm (1/2 in.) | ≥110 ksi (760 MPa) | ≥85 ksi (585 MPa) | 8% |
- Hardness plays no part in ASTM B164 acceptance, so the tensile minimums and the ordered edition decide the release, and the section size narrows which row applies.
Physical Properties
Published references place this threaded rod at a density near 8.80 g/cm³ with a melting range of 1300–1350 °C. In addition, the Curie range sits just above ambient, so a threaded rod behaves as a weakly magnetic material near room temperature.
Meanwhile, the physical properties table on the Monel 400 material page holds the thermal conductivity, the electrical resistivity and the remaining design values behind this threaded rod.
Heat Treatment
Monel 400 threaded rod softens by annealing and straightens by a low-temperature relief rather than by aging. In addition, we supply this Monel 400 threaded rod in whichever condition your duty calls for.
| Condition | Typical Treatment |
|---|---|
| Annealed | Held between 870 and 980 °C (1600–1800 °F), then cooled |
| Stress Relieved | 300–320 °C (570–610 °F) for about one hour, then air cooled |
| Custom Condition | Heat treatment according to the agreed specification |
Standards
The bar behind this threaded rod is certified to ASTM B164, while the finished fastener moves to ASTM F468 for studs and bolts and ASTM F467 for nuts. Moreover, QQ-N-281 remains the legacy military document for this threaded rod.
| Standard | Product or Application |
|---|---|
| ASTM F468 | Bolts, studs and screws in alloy 400 |
| ASTM F467 | Nuts in alloy 400 |
| ASTM B164 | Bar stock behind this threaded product |
Finally, the full standards list on the Monel 400 material page adds the European designations, the defence documents and the fastener specifications behind this threaded rod.
Dimensions
Dimensions of Monel 400 threaded rod follow the manufacturing route, the standard and the order quantity. Therefore, the table below lists typical supply ranges, so please confirm your size in the inquiry.
| Product Form | Typical Supply | Length |
|---|---|---|
| Threaded Rod | 6–64 mm dia., UNC and UNF | 1 m, 2 m, 3 m or custom |
| Metric Threaded Rod | M6–M64 | 1 m, 2 m, 3 m or custom |
| Full-Thread Studs | 6–64 mm dia. | Cut to length |
| Double-Ended Studs | M8–M36 | Cut to length |
| Custom Threaded Rod | To drawing | Custom |
Available sizes of this Monel 400 threaded rod depend on the manufacturing route, the standard, the material condition and the order quantity. Please confirm your required threaded rod size, section and length in the inquiry.
Bar stock behind this product carries ASTM B164 certification, while finished studs and bolts can also be certified to ASTM F468 and finished nuts to ASTM F467. Besides, F468 caps alloy 400 bolts at 25 HRC, which the annealed condition meets.
Surface Finishes
Finish decides what the next operation does to this material, whether that is a turning pass, a grinding pass or a welding cell. Specifically, we agree the finish on this Monel 400 threaded rod before we release the order.
| Surface Condition | Typical Use |
|---|---|
| Cold Drawn | Drawn stock giving this threaded rod close diameter control and a smooth bright skin. |
| Stress Relieved | A low-temperature relief pass on this threaded rod that holds straightness without softening it. |
| Peeled | A machined skin on this threaded rod with uniform diameter for the following turning pass. |
Meanwhile, the surface finishes table on the Monel 400 material page lists the remaining conditions we quote for this threaded rod.
Related forms from the same heat cover Monel 400 Welding Wire, Monel 400 Wire and Monel 400 Bright Bar when your threaded rod order needs them.
TECHNICAL DOCUMENTATION
Download Technical Datasheet
Get detailed information including specifications, standards, dimensions and material properties.
HOW TO START
Start Your Order in 6 Simple Steps
One coordinator carries your Monel 400 threaded rod order from first question to loading. Therefore, most orders for this Monel 400 threaded rod move from quotation to dispatch inside three weeks.
1
Send the Duty Data
Give the size, quantity, standard and the seawater or acid duty your Monel 400 threaded rod will see.
2
Fix the Condition
Then we set the delivery condition and tolerance for this Monel 400 threaded rod.
3
Review the Offer
Receive pricing for this Monel 400 threaded rod by dimension, quantity and destination port.
4
Approve the Order
Approve the specification, terms and schedule for this Monel 400 threaded rod in writing.
5
Witness Points Agreed
Any third-party inspection of this Monel 400 threaded rod is booked before production starts.
6
Dispatch and Documents
Receive this Monel 400 threaded rod with the mill certificate, packing list and shipping papers.
CERTIFICATIONS & QUALITY DOCUMENTATION
Certifications & Quality Documentation
Our production and inspection processes are certified to international standards, and every delivery ships with EN 10204 3.1 mill test certificates.
ISO 9001:2015
Quality Management System
PED 2014/68/EU
Pressure Equipment Directive
ASTM / ASME
Material Standards Compliance
EN 10204 3.1
Mill Test Certificates
FAQ
Frequently Asked Questions
Which standard covers this Monel 400 threaded rod?
ASTM B164 and ASME SB164 govern this Monel 400 threaded rod for UNS N04400 across round, square, hex and rectangular sections.
Is this Monel 400 threaded rod suitable for seawater?
Yes. This threaded rod performs well in flowing seawater, although stagnant water and silt traps raise the pitting risk on this Monel 400 threaded rod.
Can this Monel 400 threaded rod be age hardened?
No. This threaded rod is a solid-solution alloy, so cold work raises its strength and the K-500 grade covers aged duty instead.
Can this Monel 400 threaded rod be machined and welded?
Yes. This threaded rod machines to a clean finish, and GTAW with ERNiCu-7 filler joins it without a post-weld anneal.
How is the price of this Monel 400 threaded rod calculated?
Pricing follows weight for this Monel 400 threaded rod, with the nickel and copper quotations fixed on the date you receive the offer.
What is your MOQ for this Monel 400 threaded rod?
A single piece covers many common sizes of this Monel 400 threaded rod.
What are your trade terms for this Monel 400 threaded rod?
FOB covers most orders for this Monel 400 threaded rod, and EXW or CIF terms are available when you ask.
What is the lead time for this Monel 400 threaded rod?
Stock sizes of this Monel 400 threaded rod dispatch in 7 to 15 days, while made-to-order sections take longer.
Do you provide EN 10204 3.1 or 3.2 certificates for this Monel 400 threaded rod?
Yes. Every heat of this Monel 400 threaded rod ships with 3.1, and a 3.2 endorsement is booked through the order.
What information should an enquiry for this Monel 400 threaded rod include?
Please send the grade, section, diameter, length, condition, finish, quantity and destination so we can quote this Monel 400 threaded rod accurately.
REQUEST FOR QUOTATION
Need A Custom Alloy Solution?
Monel 400 threaded rod is quoted by thread form, diameter and length to ASTM B164 and F468. Send the thread callout and quantity to price this Monel 400 threaded rod.
Specifically, we review your Monel 400 threaded rod specification, confirm the condition and document scope, and return pricing with clear terms. Production then follows the signed specification, and each consignment of this Monel 400 threaded rod ships with the full paperwork set.
