01
Hastelloy B-3 Annealed Wire
Soft wire that forms and coils before it goes into a fabrication.
Request Availability →Hastelloy B-3 Wire
Hastelloy B-3 wire in annealed and spring temper for acid plant mesh, filtration cloth and spring work.
Two Tempers from One Chemistry
This Hastelloy B-3 wire ships annealed under 1200 MPa or spring temper between 1600 and 2000 MPa.
Published Working Window
Moreover, data for this Hastelloy B-3 wire gives a service band from −200 to +400 °C in both tempers.
Built for Acid-Plant Wire Duty
Furthermore, demister pads, spring clips and filtration mesh make up most of what this Hastelloy B-3 wire is drawn for.
PRODUCT OVERVIEW
About Hastelloy B-3 Wire
Hastelloy B-3 wire arrives in UNS N10675, the nickel-molybdenum grade built for hydrochloric acid up to boiling point. Chromium between 1.0 and 3.0% slows the embrittling phase, so welded joints in this wire usually enter service as welded.
We draw wire of this grade to the ordered temper, and published working temperatures run from −200 to +400 °C. We supply this Hastelloy B-3 wire to ASTM B335 and ASME SB335 in hot-worked, annealed and cold-drawn states, with the ASTM B564 forging route above 88.9 mm. Every consignment of this wire leaves with a heat-number record, the anneal temperature actually used and a set of EN 10204 3.1 papers.
Meanwhile, the full chemistry window and the physical data behind this Hastelloy B-3 wire sit on our Hastelloy B-3 material page for cross-reference.
PRODUCT FEATURES
Key Features of Hastelloy B-3 Wire
Hastelloy B-3 wire arrives in UNS N10675, the nickel-molybdenum grade that carries 1.0–3.0% chromium on purpose, which slows the embrittling phase enough that most welded joints enter service without a furnace pass. We supply ASTM B335 wire from 0.025 to 21 mm in annealed and spring-temper states for hydrogen chloride synthesis, acid regeneration and steel pickling hardware. Every Hastelloy B-3 wire consignment travels with heat-number traceability, EN 10204 3.1 mill test reports and full export documentation.
Hastelloy B-3
Two Delivery Tempers
For example, this Hastelloy B-3 wire ships annealed under 1200 MPa or spring temper at 1600–2000 MPa.
01
Demister Mesh Capability
Specifically, this Hastelloy B-3 wire weaves into pads that catch droplets inside absorption and scrubbing towers.
02
Reducing-Acid Suitability
In addition, this Hastelloy B-3 wire holds up in hydrochloric acid and other streams that carry no oxidant.
03
Stress Relief After Forming
Moreover, a 400–450 °C pass for two hours follows cold forming of this Hastelloy B-3 wire where the order calls for it.
04
Non-Magnetic Behaviour
This Hastelloy B-3 wire stays practically non-magnetic at ambient temperature in service.
05
Wide Working Window
Published data gives this Hastelloy B-3 wire a working band from −200 to +400 °C.
06
Fine Diameter Range
We draw this Hastelloy B-3 wire down through a 0.025 mm floor for instrument and filtration work.
07
Consistent Coiling
We wind every coil of this Hastelloy B-3 wire with steady layering so feeders never tangle.
08
WHY CHOOSE US
Why Choose Hastelloy B-3
Weaving, coiling and spring work each ask for a different amount of cold reduction in Hastelloy B-3 wire. Specifically, we fix the diameter, the temper and the coil weight of this Hastelloy B-3 wire before we quote it.
01
Duty Read Before Pricing
We record the medium, its concentration and its temperature for your Hastelloy B-3 wire before proposing a delivery state.
02
Certificates Tied to the Heat
Specifically, EN 10204 3.1 papers, heat numbers and dimensional records follow each Hastelloy B-3 wire consignment.
03
Welded or Machined, One Route
In addition, this Hastelloy B-3 wire flows through a single process whether your shop welds it into a vessel or turns it on a lathe.
04
Terms Stated in Writing
Quotations for this Hastelloy B-3 wire name the medium, the section, the finish and the document set rather than leaving them open.
MANUFACTURING PROCESS
Reliable Production For Critical Applications
Drawing this grade down to fine diameters starts at the melt and ends on the spool. Every stage of this Hastelloy B-3 wire route carries its heat number into the certificate.
01
Charge Weighing
We weigh nickel, molybdenum and chromium to the B335 analysis before this Hastelloy B-3 wire is melted.
02
Melting and Casting
First, the charge for this Hastelloy B-3 wire melts and casts into electrode stock with carbon held low.
03
Hot Rolling to Rod
Next, hot rolling reduces cast stock into drawing rod for this Hastelloy B-3 wire.
04
Annealing
Then, we anneal near 1066 °C and quench this Hastelloy B-3 wire between reductions.
05
Wire Drawing
After that, successive dies pull this Hastelloy B-3 wire down toward the ordered diameter.
06
Intermediate Anneals
Because this Hastelloy B-3 wire work-hardens quickly, we soften it between drawing passes.
07
Temper and Stress Relief
Subsequently, the last reduction sets this Hastelloy B-3 wire to the ordered temper, with a relief pass on request.
08
Coiling and Release
Finally, we wind this Hastelloy B-3 wire onto coils and spools and clear the heat for dispatch.
Manufacturing Facility
MANUFACTURING CAPABILITY
Advanced Production For Nickel Alloy Products
Stock lengths and made-to-order heats of Hastelloy B-3 wire leave on one production schedule. Moreover, we quote this Hastelloy B-3 wire inside our bar and rod program.
20,000+ m²
Factory Area
Hot working, annealing, drawing and pickling lines for Hastelloy B-3 wire share one site.
50+
Production Machines
Units covering hot working, annealing, drawing and pickling for this Hastelloy B-3 wire.
600 Tons
Monthly Capacity
Hastelloy B-3 wire output across stock and bespoke lots.
30+
Technical Engineers
Metallurgists who set the anneal plan and the delivery state of this Hastelloy B-3 wire against your duty.
30+ Countries
Export Reach
In addition, sealed export packing carries this Hastelloy B-3 wire to buyers on five continents.
QUALITY ASSURANCE
Strict Quality Control From Production To Delivery
Nothing leaves the yard until the heat behind your Hastelloy B-3 wire has cleared our ISO 9001 inspection route. In addition, we test this Hastelloy B-3 wire against the chemistry, tensile and surface the order names.
01
Heat Identification
We confirm the grade and heat number of this Hastelloy B-3 wire against your purchase order.
02
Chemistry Verification
Specifically, molybdenum, chromium and carbon in this Hastelloy B-3 wire go against the B335 table for your lot.
03
Tensile Verification
In addition, we report the tensile and yield results of this Hastelloy B-3 wire against the B335 minimums for every heat.
04
Certificate Assembly
Every consignment of this Hastelloy B-3 wire ships with EN 10204 3.1 papers keyed to its heat.
PRODUCT FORMS
Available Product Forms
We quote sections and delivery states for Hastelloy B-3 wire against the drawing rather than from a catalogue. In addition, the list below shows the Hastelloy B-3 wire forms ordered most often.
02
Hastelloy B-3 Spring-Temper Wire
Heavily reduced wire that holds a set in spring work.
Request Availability →
03
Hastelloy B-3 Flat Wire
Rolled flat section for seals, strip work and woven media.
Request Availability →
04
Hastelloy B-3 Shaped Wire
Profiled section drawn against your shape requirement.
Request Availability →
05
Hastelloy B-3 Custom Wire
Custom diameters, tempers and packing produced against your callout.
Request Availability →
APPLICATIONS
Engineered For Demanding Industries
Hastelloy B-3 wire suits duty where a reducing acid has to travel inside a small cross-section. Therefore, the list below sets out where this Hastelloy B-3 wire earns its keep.
Discuss Your Application →
01
Hastelloy B-3 Absorption Tower Demister Mesh
Wire woven into pads that catch droplets above absorption column sprays.
02
Hastelloy B-3 Acid Filtration Cloth
Woven cloth filtering reducing acid process liquors.
03
Hastelloy B-3 Pickling Basket Mesh
Mesh forming baskets that carry work through pickling lines.
04
Hastelloy B-3 Acid Vapour Cage Mesh
Woven mesh forming guards and cages in acid process areas.
05
Hastelloy B-3 Gasket Wire
Wire formed into seals for acid plant flanged connections.
06
Hastelloy B-3 Spring Work for Acid Valves
Spring wire holding valves and instruments in set inside acid plants.
07
Hastelloy B-3 Weaving and Knitting Stock
Wire sized for weaving and knitting acid plant filter media.
08
Hastelloy B-3 Spooled Wire for Automatic Feeders
Wire wound on spools so automatic feeders run without tangling.
TECHNICAL INFORMATION
Technical Specifications
Detailed technical information including chemical composition, mechanical properties, standards and available dimensions.
Chemical Composition
Chromium sits deliberately between 1.0 and 3.0% in this wire, and that addition is what separates the UNS N10675 window from the earlier nickel-molybdenum grades. Consequently, molybdenum holds 27.0–32.0% while carbon stops at 0.01%, so the nickel-plus-molybdenum total of this wire lands between 94.0 and 98.0%.
For every element measured against its B335 limit behind this wire, open the composition breakdown kept on the Hastelloy B-3 material page.
Mechanical Properties
Typical room-temperature ranges for UNS N10675 wire appear below, drawn from published Alloy Wire International data. Therefore the ordered temper and diameter settle the acceptance values for Hastelloy B-3 wire.
| Temper | Typical Tensile Strength | Typical Use |
|---|---|---|
| Annealed (soft) | under 1200 MPa (under 174 ksi) | Forming and coiling before fabrication |
| Spring temper | 1600–2000 MPa (232–290 ksi) | Springs, clips and retained-set parts |
- Alloy Wire International publishes these UNS N10675 wire ranges and sets the working window of this grade between −200 and +400 °C for both tempers. Moreover, the same source puts the stress-relief pass at 400–450 °C for two hours followed by air cooling. Therefore, the temper and the diameter you order govern final release on this Hastelloy B-3 wire.
Physical Properties
Reference data places the density of this wire at 9.22 g/cm³, with a melting range that closes near 1418 °C. Moreover, the annealed matrix leaves this wire essentially non-magnetic, and its elastic modulus settles near 216 GPa.
Meanwhile, the physical properties table on the Hastelloy B-3 material page holds the conductivity and expansion figures behind this wire.
Delivery Conditions
Hastelloy B-3 wire ships in the delivery states below. Specifically, the ordered temper is the delivered state, and the certificate records any stress-relief pass that followed.
| Delivery State | Typical Diameter | Notes |
|---|---|---|
| Annealed (soft) | 0.025–21 mm | Softest state, formed and coiled before fabrication |
| Spring temper | 0.025–21 mm | Heavily reduced, holds a set in spring work |
| Stress relieved | 0.025–21 mm | Relieved at 400–450 °C for two hours and air cooled after forming |
| Flat and shaped sections | to your drawing | Flat stock from 0.15 mm thick and to 12.00 mm wide, shaped profiles to 45 mm² |
Delivery note: UNS N10675 takes no strength from aging, so the ordered temper is the delivered state, and published working temperatures from −200 to +400 °C cover the duty this Hastelloy B-3 wire usually serves.
Standards
Wire of this wire sits outside ASTM B335, because that document names rod only, so the German and international routes carry it instead. Specifically, DIN 17753 and ISO 9724 cover this wire in coil, spool and straight length. Moreover, no aerospace document reaches the grade, so the mill certificate and the ordered temper settle acceptance.
| Standard | Product or Application |
|---|---|
| DIN 17753 | German wrought nickel alloy wire document |
| ISO 9724 | International wire document |
| ASTM B335 (base metal) | Rod document that stops short of wire |
Finally, the full standards list on the Hastelloy B-3 material page adds the plate, tube, fitting and flange documents plus the Chinese designation behind this wire.
Dimensions
Dimensions of Hastelloy B-3 wire follow the route, the document and the order quantity. Therefore, typical supply ranges sit in the table below, so please confirm your sizes in the inquiry.
| Product Form | Typical Supply | Length |
|---|---|---|
| Wire, Coil or Spool | 0.025–21 mm dia., typical | Coil, spool or custom |
| Fine Wire | 0.025–0.80 mm dia. | Spool |
| Spring-Temper Wire | 0.10–20 mm dia. | Coil or spool |
| Flat Wire | 0.15–12.0 mm section | Coil or spool |
| Shaped Wire | To 45 mm² section | Coil or spool |
| Straightened and Cut Wire | 1.0–10 mm dia. | Straight lengths |
| Custom Wire | To drawing | Custom |
Available sizes of this Hastelloy B-3 wire depend on the route, the document, the state and the lot size. Please confirm the size, section and length you need for this wire in the inquiry.
ASTM B335 names rod only, so wire of this grade ships on DIN 17753 and ISO 9724 instead. Moreover, the temper you order is the delivered state, and we quote this wire by diameter, temper and coil or spool weight.
Surface Finishes
The surface you order decides how this wire behaves once it reaches a hydrogen chloride synthesis unit, an absorption tower or an acid regeneration loop. Moreover, most stock of this wire leaves the yard solution annealed and pickled. Therefore, we confirm the finish and the straightness band on this Hastelloy B-3 wire before we write the offer.
| Surface Condition | Typical Use |
|---|---|
| Solution Annealed and Pickled | Annealing followed by acid descaling leaves this wire scale-free for hydrogen chloride service. |
| Bright Annealed | Protective-atmosphere annealing leaves this wire oxide-free for instrument and vacuum work. |
| Spooled | This wire wound onto spools or carriers at an even tension. |
In addition, the surface finishes table recorded on the Hastelloy B-3 material page lists the remaining conditions quoted for this wire.
Related forms from the same heat cover Hastelloy B-3 Bright Bar, Hastelloy B-3 Centreless-Ground Rod and Hastelloy B-3 Cold-Drawn Bar when your wire order needs them.
TECHNICAL DOCUMENTATION
Download Technical Datasheet
Get detailed information including specifications, standards, dimensions and material properties.
HOW TO START
Start Your Order in 6 Simple Steps
One coordinator stays with your Hastelloy B-3 wire enquiry from the first question through to loading. Therefore, stock sizes of this Hastelloy B-3 wire dispatch inside fifteen days, while a fresh annealed heat runs about twenty-five.
1
Send the Medium Data
Give us the medium, its concentration and its temperature, plus the size, quantity and standard this Hastelloy B-3 wire will face.
2
Fix the State
Then we set the annealing cycle, the delivery state and the tolerance band for this Hastelloy B-3 wire.
3
Review the Offer
Pricing for this Hastelloy B-3 wire arrives by size, quantity and destination port.
4
Approve the Order
You confirm the specification, the terms and the schedule of this Hastelloy B-3 wire in writing.
5
Witness Points Agreed
We book any third-party inspection or dimensional review of this Hastelloy B-3 wire before production starts.
6
Dispatch and Documents
This Hastelloy B-3 wire arrives with mill papers, a packing list and the certificate set.
CERTIFICATIONS & QUALITY DOCUMENTATION
Certifications & Quality Documentation
Our production and inspection processes are certified to international standards, and every delivery ships with EN 10204 3.1 mill test certificates.
ISO 9001:2015
Quality Management System
PED 2014/68/EU
Pressure Equipment Directive
ASTM / ASME
Material Standards Compliance
EN 10204 3.1
Mill Test Certificates
FAQ
Frequently Asked Questions
Which specification covers this Hastelloy B-3 wire?
DIN 17753 and ISO 9724 govern this Hastelloy B-3 wire, because the ASTM nickel-molybdenum rod standard names rod rather than wire.
What diameters does this Hastelloy B-3 wire span?
Published supply data for this Hastelloy B-3 wire runs from 0.025 to 21 mm in round section, with flat stock from 0.15 mm thick.
Which delivery states are available for this Hastelloy B-3 wire?
This wire ships annealed under 1200 MPa or spring temper at 1600–2000 MPa, plus a 400–450 °C relief pass on request.
Does this Hastelloy B-3 wire respond to aging?
No. UNS N10675 hardens only through cold work, so the temper you order is the state this Hastelloy B-3 wire arrives in.
How is the price of this Hastelloy B-3 wire calculated?
Weight in kilograms drives pricing for this Hastelloy B-3 wire, with the nickel and molybdenum quotations fixed on the date the offer is issued.
What is your MOQ for this Hastelloy B-3 wire?
One spool covers many common diameters of this Hastelloy B-3 wire.
What are your trade terms for this Hastelloy B-3 wire?
We quote FOB as standard for this Hastelloy B-3 wire, and EXW, CIF or DAP terms follow once we fix the destination.
What is the lead time for this Hastelloy B-3 wire?
Expect 7 to 15 days on stock sizes of this Hastelloy B-3 wire, while a custom draw takes longer.
Do you provide EN 10204 3.1 or 3.2 certificates for this Hastelloy B-3 wire?
Every coil of this Hastelloy B-3 wire ships with EN 10204 3.1, and we book a 3.2 endorsement through the order.
What information should an enquiry for this Hastelloy B-3 wire include?
Please send the diameter, temper, coil weight, quantity and destination so we can quote this Hastelloy B-3 wire accurately.
REQUEST FOR QUOTATION
Need A Custom Alloy Solution?
We quote Hastelloy B-3 wire by diameter, temper and coil or spool weight. Send those figures with your quantity so we can price this Hastelloy B-3 wire.
We walk your Hastelloy B-3 wire inquiry through the anneal, the finish and the document scope, then quote on clear terms. Production then follows the signed sheet, and every consignment of this Hastelloy B-3 wire leaves with the complete paper set.
