01
Annealed Nickel Wire
Soft annealed wire that weaves, knits and redraws without cracking.
Request Availability →Nickel 200 / 201 Wire
Commercially pure nickel wire from 0.2 to 12 mm in annealed and cold-drawn states for mesh, anodes and cold-formed parts.
Alkali Service Stock
We match every Nickel 200 / 201 wire we quote to the caustic duty your plant describes.
Grade Settled Before Pricing
Specifically, we fix grade 200 or grade 201 for your wire against the 315 °C service limit before pricing it.
Papers Ready for Inward Inspection
Moreover, your Nickel 200 / 201 wire arrives with mill certificate, packing list and export documents in one set.
PRODUCT OVERVIEW
About Nickel 200 / 201 Wire
Nickel 200 / 201 wire arrives in UNS N02200 or N02201, the commercially pure grades holding 99.0% nickel and above. Caustic soda, potash and alkaline salt solutions leave this wire untouched at every concentration.
We supply Nickel 200 / 201 wire to ASTM B160 and ASME SB160 in hot-worked, cold-worked and annealed conditions. Your order for this wire carries heat-number records and EN 10204 3.1 paperwork for goods-in checks. Moreover, section, straightness and finish on the wire are settled before the order is released.
Meanwhile, the chemistry and the design values behind Nickel 200 / 201 wire sit on our Nickel 200 / 201 material page for cross-reference.
PRODUCT FEATURES
Key Features of Nickel 200 / 201 Wire
Nickel 200 / 201 wire is supplied in UNS N02200 or N02201, the commercially pure grades that hold 99.0% nickel and above. We provide ASTM B160 and ASME SB160 wire from 0.2 to 12 mm in annealed and cold-drawn states for caustic plants, chlor-alkali works and electrochemical lines. Every Nickel 200 / 201 wire order carries heat-number traceability, EN 10204 3.1 mill test reports and export documentation.
Nickel 200 / Nickel 201
Wide Temper Range
For example, this wire ships annealed, cold-drawn or temper rolled.
01
Fine Diameter Capability
Specifically, this wire draws down to fine sizes for weaving and filtration.
02
Alkali Resistance
In addition, this wire holds its surface in caustic and alkaline salt solutions.
03
Current-Carrying Duty
Moreover, the conductivity of this wire suits mesh current collectors and contacts.
04
Consistent Coiling
We wind this wire with controlled layering so feeders run without tangling.
05
Cold-Forming Ductility
Annealed this wire bends, knits and heads without cracking.
06
Full Traceability
Every coil of this wire carries heat numbers and EN 10204 3.1 documents.
07
WHY CHOOSE US
Why Choose Nickel 200 / Nickel 201
Mesh and cold-headed parts ask for temper control first in Nickel 200 / 201 wire. Specifically, we fix the diameter, temper and coil weight of this wire before we quote it.
01
Duty Read Before Pricing
We record your caustic concentration, temperature and current load before proposing a condition for this wire.
02
Certificates Tied to the Heat
Specifically, EN 10204 3.1 papers, heat numbers and PMI records follow each wire delivery.
03
Trial Pieces and Container Lots
In addition, this wire moves through one route whether you need a single length or a full container.
04
Terms Stated in Writing
Quotations for this wire name the grade, section, condition and document set instead of leaving them open.
MANUFACTURING PROCESS
Reliable Production For Critical Applications
Wire production for Nickel 200 / 201 wire runs from charge weighing to final spooling. We log every stage of this wire route against its heat number.
01
Charge Weighing
We weigh nickel cathode so this wire melts inside the N02200 or N02201 window.
02
Melting and Casting
First, the charge for this wire melts and casts into electrode stock.
03
Hot Rolling to Rod
Next, hot rolling reduces cast stock into drawing rod for this wire.
04
Annealing and Descaling
Then, we anneal and descale the rod before this wire enters the draw bench.
05
Wire Drawing
After that, successive dies pull this wire down to the ordered diameter.
06
Final Anneal or Temper
Subsequently, this wire is either softened or held at a controlled cold-work level.
07
Coiling and Packing
We wind this wire onto coils and spools with controlled layering.
08
Inspection and Release
Finally, chemistry and strength checks clear this wire for dispatch.
Manufacturing Facility
MANUFACTURING CAPABILITY
Advanced Production For Nickel Alloy Products
Stock, cut lengths and job lots of Nickel 200 / 201 wire leave on one schedule. We confirm section and finish of this wire before release. Moreover, this wire sits inside our Nickel 200 / 201 bar and rod program.
20,000+ m²
Factory Area
Specifically, melting, forging, drawing and inspection halls serving Nickel 200 / 201 wire under one roof.
50+
Production Machines
Equipment covering hot working, annealing and cold finishing for this wire.
600 Tons
Monthly Capacity
Nickel 200 / 201 wire output across stock and made-to-order sizes.
30+
Technical Engineers
Metallurgists who set the grade and condition of this wire against your duty.
30+ Countries
Export Reach
In addition, documented logistics carry this wire worldwide.
QUALITY ASSURANCE
Strict Quality Control From Production To Delivery
No Nickel 200 / 201 wire leaves the yard before the heat has passed our ISO 9001 inspection route. In addition, we check this wire against the chemistry, mechanical properties, dimensions and surface the order names.
01
Heat Identification
We confirm the grade and heat number of this wire against your purchase order.
02
Dimensional Verification
Specifically, size, length and straightness of this wire go against standard and drawing tolerances.
03
Property Testing
In addition, tensile, hardness and NDT checks run wherever your wire specification requires them.
04
Certificate Assembly
Every wire delivery carries EN 10204 3.1 documents keyed to the heat number.
PRODUCT FORMS
Available Product Forms
Several conditions and variants of Nickel 200 / 201 wire cover different machining and service needs. Therefore, the list below shows the Wire variants we quote most often.
02
Cold-Drawn Nickel Wire
Drawn wire with higher strength for screens and formed parts.
Request Availability →
03
Temper-Rolled Wire
Temper-rolled wire for contacts that must hold a set.
Request Availability →
04
Fine Nickel Wire
Fine wire for weaving and filtration media.
Request Availability →
05
Straightened and Cut Wire
Wire straightened and cut for cold-forming blanks.
Request Availability →
06
Wire Rod
Rod stock from 6.0 to 20.0 mm feeding downstream redraw lines.
Request Availability →
07
Custom Wire
Custom diameters, tempers and packing produced to your callout.
Request Availability →
APPLICATIONS
Engineered For Demanding Industries
Nickel 200 / 201 wire is chosen where conductivity meets woven or formed geometry. Specifically, the applications below show where this wire serves.
Discuss Your Application →
01
Woven Nickel Mesh
Wire woven into screens for alkaline process streams.
02
Knitted Mesh
Knitted wire used in demisters and mist eliminators.
03
Anode Baskets
Wire forms anode baskets in electroplating lines.
04
Plating Hooks
Hooks carrying work through plating baths.
05
Spring Contacts
Contacts that must hold force inside electrical assemblies.
06
Battery Mesh
Mesh current collectors inside battery and cell builds.
07
Filtration Media
Filter elements for hot alkaline and neutral streams.
08
Cold-Formed Fasteners
Annealed wire cold-headed into small fasteners.
TECHNICAL INFORMATION
Technical Specifications
Detailed technical information including chemical composition, mechanical properties, standards and available dimensions.
Chemical Composition
UNS N02200 and N02201 share one nickel balance of 99.0% minimum, and the carbon ceiling alone separates the two grades inside this wire, at 0.15% for grade 200 against 0.02% for grade 201. Above all, that carbon gap decides how far this wire can run in hot service.
For an element-by-element account of every limit, open the composition breakdown held on the Nickel 200 / 201 material page for this wire.
Mechanical Properties
Typical room-temperature ranges for UNS N02200 and N02201 wire appear below, taken from published alloy references. The ordered temper and diameter decide the acceptance values for Nickel 200 / 201 wire.
| Condition | Tensile Strength | Yield Strength (0.2%) | Elongation |
|---|---|---|---|
| Annealed, typical | 55–95 ksi (380–655 MPa) | 15–45 ksi (105–310 MPa) | 30–50% |
| Cold-drawn, typical | 100–185 ksi (690–1275 MPa) | 80–175 ksi (550–1205 MPa) | 2–15% |
- The figures above stand as typical published ranges for UNS N02200 and N02201 wire rather than acceptance minima, because the ordered temper and diameter govern the release values.
Physical Properties
Published references give this wire a density near 8.89 g/cm³ and a melting range of 1435–1446 °C. Moreover, the two grades part company on thermal conductivity, so design work on this wire starts from the grade actually ordered.
In addition, the physical properties table on the Nickel 200 / 201 material page carries the thermal conductivity, the electrical resistivity and the remaining design values behind this wire.
Delivery Conditions
Nickel 200 / 201 wire ships in the delivery states below. Specifically, hot-rolled states supply drawing stock while cold-drawn states are finished product wire.
| Delivery State | Typical Diameter | Notes |
|---|---|---|
| Hot rolled wire rod | 6.0–20.0 mm | Scale-covered drawing stock, supplied for redraw |
| Hot rolled, annealed | 5.5–19 mm | Coils softened so downstream forming runs clean |
| Hot rolled, annealed and pickled | 5.5–19 mm | Descaled to a bright surface before dispatch |
| Cold drawn, annealed | 0.2–12 mm | Softest product wire, offering the best ductility |
| Cold drawn, temper | 0.2–12 mm | Higher strength for screens and formed components |
Delivery note: hot-rolled states travel as coiled wire rod for redraw, while finished product wire ships to DIN 17753 in the annealed or cold-drawn state.
Standards
ASTM B160 stops at solid bar sections, so this wire is quoted to DIN 17753 and ISO 9724 instead, with ASTM International covering the bar grades alone. Moreover, those European documents carry the wire-specific tolerances for this wire.
| Standard | Product or Application |
|---|---|
| DIN 17753 | Wrought nickel wire, delivery conditions |
| ISO 9724 | Nickel and nickel alloy wire |
| ASTM B160 | Bar and rod only; wire falls outside its scope |
Finally, the full standards list on the Nickel 200 / 201 material page adds the European designations, the pressure-code documents and the forgings specification behind this wire.
Dimensions
Dimensions of Nickel 200 / 201 wire follow the manufacturing route, the standard and the order quantity. The table below lists typical supply ranges, so please confirm your size in the inquiry.
| Product Form | Typical Supply | Length |
|---|---|---|
| Wire (Coil / Spool) | 0.2–12 mm dia., typical | Coil, spool or custom |
| Wire Rod (Drawing Stock) | 6.0–20.0 mm dia. | Coil |
| Fine Wire | 0.10–0.80 mm dia. | Spool |
| Straightened and Cut Wire | 1.0–12 mm dia. | Straight lengths |
| Custom Wire | To drawing | Custom |
Available sizes of this wire depend on the manufacturing route, the standard, the material condition and the order quantity. Please confirm your required wire size, section and length in the inquiry.
Surface Finishes
Finish decides what happens at the next operation, whether that is a turning pass, a grinding pass or a welding cell. Specifically, we agree the finish on this Nickel 200 / 201 wire before we release the order.
| Surface Condition | Typical Use |
|---|---|
| Bright Annealed | Protective-atmosphere annealing leaves this wire oxide-free. |
| Pickled | Acid cleaning descaled this wire after the anneal. |
| Coated | A light lubricant film on this wire for downstream redrawing. |
Meanwhile, the surface finishes table on the Nickel 200 / 201 material page lists the remaining conditions we quote for this wire.
Related forms from the same heat cover Nickel 200 / 201 Bright Bar, Nickel 200 / 201 Centreless-Ground Rod and Nickel 200 / 201 Cold-Drawn Bar when your wire order needs them.
TECHNICAL DOCUMENTATION
Download Technical Datasheet
Get detailed information including specifications, standards, dimensions and material properties.
HOW TO START
Start Your Order in 6 Simple Steps
One coordinator carries your Nickel 200 / 201 wire order from first question to loading. Therefore, most orders for this wire move from quotation to dispatch inside three weeks.
1
Send the Duty Data
Give the size, quantity, standard and the caustic duty your wire will see.
2
Fix the Grade and Condition
Then we set grade 200 or 201 and the delivery condition for this wire.
3
Review the Offer
Receive pricing for this wire by dimension, quantity and destination port.
4
Approve the Order
Approve the specification, terms and schedule for this wire in writing.
5
Witness Points Agreed
Any third-party inspection of this wire is booked before production starts.
6
Dispatch and Documents
Receive this wire with the mill certificate, packing list and shipping papers.
CERTIFICATIONS & QUALITY DOCUMENTATION
Certifications & Quality Documentation
Our production and inspection processes are certified to international standards, and every delivery ships with EN 10204 3.1 mill test certificates.
ISO 9001:2015
Quality Management System
PED 2014/68/EU
Pressure Equipment Directive
ASTM / ASME
Material Standards Compliance
EN 10204 3.1
Mill Test Certificates
FAQ
Frequently Asked Questions
Which specification covers Nickel 200 / 201 Wire?
DIN 17753 and ISO 9724 cover this wire, because ASTM B160 reaches solid bar sections only.
What diameters does this wire span?
Product wire of this wire typically runs from 0.2 to 12 mm, and drawing stock spans 6.0 to 20.0 mm.
Which tempers are available for this wire?
This wire ships annealed, cold-drawn or temper rolled, with finer tempers quoted by diameter.
Do wire strength figures hold after straightening this wire?
No. Cold-worked values for this wire lapse once it is straightened and cut, so order the temper your parts need.
How is the price of this wire calculated?
Pricing follows weight for this wire, with the prevailing nickel quotation applied on the order date.
What is your MOQ for this wire?
One spool covers many common diameters of this wire.
What are your trade terms for this wire?
FOB covers most orders for this wire, and EXW or CIF terms are available when you ask.
What is the lead time for this wire?
Stock sizes of this wire dispatch in 7 to 15 days, while custom drawing takes longer.
Do you provide EN 10204 3.1 or 3.2 certificates for this wire?
Yes. Every coil of this wire ships with 3.1, and a 3.2 endorsement is booked through the order.
What information should an enquiry for this wire include?
Please send diameter, temper, coil weight, standard and destination so we can quote this wire accurately.
REQUEST FOR QUOTATION
Need A Custom Alloy Solution?
Nickel 200 / 201 wire from Southerly Alloy covers standard and custom supply to ASTM B160. Send your size, quantity and condition for this wire, along with your destination port, to receive a quotation.
Specifically, we review your specification for this wire, confirm the grade and annealing route, and return pricing with clear terms. Production then follows the approved specification, and each delivery of this wire ships with complete documentation.
