01
Incoloy 800/800H/800HT Annealed 800 Series Wire
Soft wire that forms and coils before hot service.
Request Availability →Incoloy 800 / 800H / 800HT Wire
Incoloy 800/800H/800HT wire to BS 3075 NA15 in annealed and spring-temper states for furnace mesh, fasteners and clips.
One B408 Table, Three Designations
Carbon and the Al+Ti total decide whether this Incoloy 800/800H/800HT wire ships as N08800, N08810 or N08811.
Coarse-Grain Heats Verified
Moreover, every 800H and 800HT wire lot carries an E112 grain-size record of ASTM 5 or coarser.
Creep Design Above 593 °C
Furthermore, we name the ASME code cases behind this Incoloy 800/800H/800HT wire so your design basis arrives with the price.
PRODUCT OVERVIEW
About Incoloy 800 / 800H / 800HT Wire
Incoloy 800 / 800H / 800HT wire arrives in the iron-nickel-chromium family whose design divide sits at 593 °C. Above 593 °C, 800H and 800HT stock of this Incoloy 800/800H/800HT wire holds creep strength far longer under load.
We supply Incoloy 800/800H/800HT wire to ASTM B408 and ASME SB408 in hot-worked, solution-annealed and cold-drawn conditions. Your order for this 800 series wire carries heat-number records and EN 10204 3.1 paperwork for goods-in checks. Besides, the designation, anneal and finish on the wire are agreed before the heat is booked.
Meanwhile, the chemistry and the design values behind Incoloy 800/800H/800HT wire sit on our Incoloy 800/800H/800HT material page for cross-reference.
PRODUCT FEATURES
Key Features of Incoloy 800 / 800H / 800HT Wire
Incoloy 800/800H/800HT wire arrives in UNS N08800, N08810 and N08811, the iron-nickel-chromium family whose design divide sits at 593 °C. We provide ASTM B408 wire from 0.025 to 21 mm in annealed and spring-temper states for furnace builders, reformer fabricators and heat-treatment shops. Every Incoloy 800/800H/800HT wire order carries heat-number traceability, EN 10204 3.1 mill test reports and full export documentation.
Incoloy 800 / 800H / 800HT
Two Delivery Tempers
For example, this Incoloy 800/800H/800HT wire ships annealed at 600–800 MPa or spring temper at 800–1100 MPa.
01
Hot Mesh Capability
Specifically, this Incoloy 800/800H/800HT wire weaves into belts and baskets that cycle through furnaces.
02
Stress-Relief After Forming
In addition, a 450–470 °C pass follows cold forming of this Incoloy 800/800H/800HT wire where the order calls for it.
03
Non-Magnetic Behaviour
Moreover, this Incoloy 800/800H/800HT wire stays non-magnetic through its working range.
04
Carburizing Atmosphere Resistance
This Incoloy 800/800H/800HT wire holds its surface in carburizing and oxidizing furnace gas.
05
Sensitization Band Noted
However, we route hot-formed this Incoloy 800/800H/800HT wire around the 425–815 °C band on heavy sections.
06
Fine Diameter Range
We draw this Incoloy 800/800H/800HT wire down to 0.025 mm for instrument and mesh work.
07
Consistent Coiling
Every coil of this Incoloy 800/800H/800HT wire is wound with controlled layering so feeders run without tangling.
08
WHY CHOOSE US
Why Choose Incoloy 800 / 800H / 800HT
Mesh weaving and spring work ask for temper control first in Incoloy 800/800H/800HT wire. Specifically, we fix the diameter, temper and coil weight of this 800 series wire before we quote it.
01
Duty Read Before Pricing
We record the temperature, the atmosphere and the designation your Incoloy 800/800H/800HT wire will meet before proposing a delivery condition.
02
Certificates Tied to the Heat
Specifically, EN 10204 3.1 papers, heat numbers and E112 grain records follow each Incoloy 800/800H/800HT wire delivery.
03
Trial Pieces and Container Lots
In addition, this Incoloy 800/800H/800HT wire moves through one route whether you need a single length or a full container.
04
Terms Stated in Writing
Quotations for this Incoloy 800/800H/800HT wire name the designation, section, finish and document set instead of leaving them open.
MANUFACTURING PROCESS
Reliable Production For Critical Applications
Wire production for Incoloy 800/800H/800HT wire runs from charge weighing to final spooling. We log every stage of this 800 series wire route against its heat number.
01
Charge Weighing
We weigh electrolytic nickel, chromium and iron to the B408 window before this Incoloy 800/800H/800HT wire melts.
02
Melting and Casting
First, the charge for this Incoloy 800/800H/800HT wire melts and casts into electrode stock.
03
Hot Rolling to Rod
Next, hot rolling reduces cast stock into drawing rod for this Incoloy 800/800H/800HT wire.
04
Annealing
Then, we anneal and descale this Incoloy 800/800H/800HT wire between reductions.
05
Wire Drawing
After that, successive dies pull this Incoloy 800/800H/800HT wire down to the ordered diameter.
06
Intermediate Anneals
Because this Incoloy 800/800H/800HT wire work-hardens, we soften it between drawing passes.
07
Temper and Stress Relief
Subsequently, the last reduction sets this Incoloy 800/800H/800HT wire to the ordered temper, and a 450–470 °C relief follows where specified.
08
Coiling and Release
Finally, we wind this Incoloy 800/800H/800HT wire onto coils and spools and clear the heat for dispatch.
Manufacturing Facility
MANUFACTURING CAPABILITY
Advanced Production For Nickel Alloy Products
Stock lengths and made-to-order lots of Incoloy 800/800H/800HT wire leave on one schedule. Moreover, this Incoloy 800/800H/800HT wire sits inside our bar and rod program.
20,000+ m²
Factory Area
Specifically, melting, forging, annealing and inspection halls serve Incoloy 800/800H/800HT wire under one roof.
50+
Production Machines
Equipment covering hot working, solution annealing and cold finishing for this Incoloy 800/800H/800HT wire.
600 Tons
Monthly Capacity
Incoloy 800/800H/800HT wire output across stock and made-to-order sizes.
30+
Technical Engineers
Metallurgists who set the anneal plan and document scope of this Incoloy 800/800H/800HT wire against your duty.
30+ Countries
Export Reach
In addition, documented logistics carry this Incoloy 800/800H/800HT wire worldwide.
QUALITY ASSURANCE
Strict Quality Control From Production To Delivery
No Incoloy 800/800H/800HT wire leaves the yard before its heat has cleared our ISO 9001 inspection route. In addition, we check this 800 series wire against the chemistry, grain size, dimensions and surface the order names.
01
Heat Identification
We confirm the designation and heat number of this Incoloy 800/800H/800HT wire against your purchase order.
02
Grain-Size Verification
Specifically, 800H and 800HT stock of this Incoloy 800/800H/800HT wire goes against ASTM 5 or coarser per E112.
03
Dimensional Verification
In addition, the size, length and straightness of this Incoloy 800/800H/800HT wire go against standard and drawing tolerances.
04
Certificate Assembly
Every consignment of this Incoloy 800/800H/800HT wire carries EN 10204 3.1 documents keyed to the heat number.
PRODUCT FORMS
Available Product Forms
Conditions and variants of Incoloy 800/800H/800HT wire cover different machining and service needs. In addition, the list below sets out the Incoloy 800/800H/800HT Wire variants we quote most often.
02
Incoloy 800/800H/800HT Spring-Temper Wire
Heavily reduced wire that holds a set in hot fixtures.
Request Availability →
03
Incoloy 800/800H/800HT Woven Mesh Wire
Wire sized for weaving conveyor belts and furnace mesh.
Request Availability →
04
Incoloy 800/800H/800HT Fine 800 Series Wire
Fine wire for instrument and hot-end sensor parts.
Request Availability →
05
Incoloy 800/800H/800HT Straightened and Cut Wire
Wire straightened and cut for heading and pin blanks.
Request Availability →
06
Incoloy 800/800H/800HT Custom 800 Series Wire
Custom diameters, tempers and packing produced to your callout.
Request Availability →
APPLICATIONS
Engineered For Demanding Industries
Incoloy 800/800H/800HT wire is chosen where hot service has to sit inside a small cross section. Consequently, the applications below show where this 800 series wire serves.
Discuss Your Application →
01
Incoloy 800/800H/800HT Furnace Conveyor Mesh
Wire woven into belts carrying work through hot zones.
02
Incoloy 800/800H/800HT Heat-Treatment Basket Mesh
Mesh wire forming baskets for repeated furnace cycles.
03
Incoloy 800/800H/800HT Hot Fixture Springs
Springs holding fixtures closed at temperature.
04
Incoloy 800/800H/800HT Fireproof Cable Elements
Wire serving cable constructions that survive fire tests.
05
Incoloy 800/800H/800HT Burner Grid Ties
Tie wire securing burner grids and refractory anchors.
06
Incoloy 800/800H/800HT Hot Filter Media
Woven media filtering hot gas and process streams.
07
Incoloy 800/800H/800HT Fastener Heading Stock
Wire feeding cold-heading lines for hot-service fasteners.
08
Incoloy 800/800H/800HT Lock Wire for Hot Zones
Wire locking fasteners inside furnace equipment.
TECHNICAL INFORMATION
Technical Specifications
Detailed technical information including chemical composition, mechanical properties, standards and available dimensions.
Chemical Composition
ASTM B408 holds nickel between 30.0% and 35.0% and chromium between 19.0% and 23.0% for this wire, with iron as the balance of the melt. Moreover, the carbon window and the Al+Ti total decide whether a heat reads N08800, N08810 or N08811. Besides, all three designations sit on one and the same B408 composition table.
For the full three-column element set, open the composition breakdown held on the Incoloy 800/800H/800HT material page for this wire.
Mechanical Properties
Typical room-temperature ranges for the series wire appear below, taken from published Alloy Wire International data. Therefore the ordered temper and diameter decide the acceptance values for Incoloy 800/800H/800HT wire.
| Temper | Typical Tensile Strength | Typical Use |
|---|---|---|
| Annealed (soft) | 600–800 MPa (87–116 ksi) | Forming and coiling before hot service |
| Spring temper | 800–1100 MPa (116–160 ksi) | Springs, clips and fixtures needing a set |
- Alloy Wire International publishes these ranges for the series, and a stress-relief pass at 450–470 °C for 0.5 to 1 hour follows cold forming where the order calls for it, so the ordered temper and diameter govern final release on this Incoloy 800/800H/800HT wire.
Physical Properties
Published references place this wire at a density near 7.94 g/cm³ with a melting range of 1357–1385 °C. Moreover, the Curie temperature sits near −115 °C, so this wire stays non-magnetic in service. Besides, the austenitic matrix keeps these values stable across all three designations.
Meanwhile, the physical properties table on the Incoloy 800/800H/800HT material page holds the modulus, the thermal expansion and the remaining design values behind this wire.
Delivery Conditions
Incoloy 800/800H/800HT wire ships in the delivery states below. Specifically, the ordered temper is the delivered state, and the certificate records any stress-relief pass that followed.
| Delivery State | Typical Diameter | Notes |
|---|---|---|
| Annealed (soft) | 0.025–21 mm | Softest state, formed and coiled before service |
| Spring temper | 0.10–8.0 mm | Heavily reduced, holds a set in hot fixtures |
| Stress relieved | 0.10–12 mm | Relieved at 450–470 °C after cold forming |
Delivery note: the family gains no strength from aging, so the ordered temper is the delivered state and the certificate records the stress-relief pass where one ran.
Standards
ASTM B408 from ASTM International defines the grade chemistry but stops short of wire, so this wire ships against BS 3075 NA15 and DIN 17753. Moreover, ISO 9724 covers wire of this wire internationally. Besides, no AMS wire document was found for the family, so none is printed here.
| Standard | Product or Application |
|---|---|
| BS 3075 NA15 | British wire document for the 800 series |
| DIN 17753 | German wire document for the 800 series |
| ISO 9724 | ISO wire document for nickel alloys |
Finally, the full standards list on the Incoloy 800/800H/800HT material page adds the ASME code cases, the European designations and the remaining product documents behind this wire.
Dimensions
Dimensions of Incoloy 800/800H/800HT wire follow the manufacturing route, the standard and the order quantity. Therefore, the table below lists typical supply ranges, so please confirm your size in the inquiry.
| Product Form | Typical Supply | Length |
|---|---|---|
| Wire (Coil or Spool) | 0.025–21 mm dia., typical | Coil, spool or custom |
| Fine Wire | 0.025–0.80 mm dia. | Spool |
| Spring-Temper Wire | 0.10–8.0 mm dia. | Coil or spool |
| Woven Mesh Wire | 0.10–3.0 mm dia. | Coil |
| Straightened and Cut Wire | 1.0–10 mm dia. | Straight lengths |
| Custom Wire | To drawing | Custom |
Available sizes of this Incoloy 800/800H/800HT wire depend on the manufacturing route, the standard, the material condition and the order quantity. Please confirm your required wire size, section and length in the inquiry.
Surface Finishes
Finish decides how this wire scales, machines and clears your incoming checks, and 800H and 800HT normally ship solution annealed so the coarse grain survives to the end of the route. Specifically, we fix the finish on this Incoloy 800/800H/800HT wire before the order is released.
| Surface Condition | Typical Use |
|---|---|
| Bright Annealed | Protective-atmosphere annealing leaves this wire oxide-free and ready to draw. |
| Pickled | Acid cleaning descaled this wire after the anneal. |
| Coated | A light carrier film on this wire that protects it during downstream redrawing. |
Meanwhile, the surface finishes table on the Incoloy 800/800H/800HT material page lists the remaining conditions we quote for this wire.
Related forms from the same heat cover Incoloy 800/800H/800HT Bright Bar, Incoloy 800/800H/800HT Centreless-Ground Rod and Incoloy 800/800H/800HT Cold-Drawn Bar when your wire order needs them.
TECHNICAL DOCUMENTATION
Download Technical Datasheet
Get detailed information including specifications, standards, dimensions and material properties.
HOW TO START
Start Your Order in 6 Simple Steps
One coordinator carries your Incoloy 800/800H/800HT wire order from first question to loading. Therefore, most orders for this 800 series wire move from quotation to dispatch inside three weeks.
1
Send the Duty Data
Give the designation, size, quantity, standard and the temperature your Incoloy 800/800H/800HT wire will see.
2
Fix the Condition
Then we set the anneal, grain-size requirement and tolerance for this Incoloy 800/800H/800HT wire.
3
Review the Offer
Receive pricing for this Incoloy 800/800H/800HT wire by dimension, quantity and destination port.
4
Approve the Order
Approve the specification, terms and schedule for this Incoloy 800/800H/800HT wire in writing.
5
Witness Points Agreed
Any third-party inspection or grain-size review of this Incoloy 800/800H/800HT wire is booked before production starts.
6
Dispatch and Documents
Receive this Incoloy 800/800H/800HT wire with the mill certificate, packing list and shipping papers.
CERTIFICATIONS & QUALITY DOCUMENTATION
Certifications & Quality Documentation
Our production and inspection processes are certified to international standards, and every delivery ships with EN 10204 3.1 mill test certificates.
ISO 9001:2015
Quality Management System
PED 2014/68/EU
Pressure Equipment Directive
ASTM / ASME
Material Standards Compliance
EN 10204 3.1
Mill Test Certificates
FAQ
Frequently Asked Questions
Which specification covers this Incoloy 800/800H/800HT wire?
BS 3075 NA15, DIN 17753 and ISO 9724 govern this Incoloy 800/800H/800HT wire, because ASTM B408 defines the chemistry but stops short of wire.
What diameters does this Incoloy 800/800H/800HT wire span?
Product wire of this Incoloy 800/800H/800HT wire typically runs from 0.025 to 21 mm, depending on the ordered temper.
Which delivery states are available for this Incoloy 800/800H/800HT wire?
This wire ships annealed at 600–800 MPa or spring temper at 800–1100 MPa, with a stress-relief pass on request.
Does this Incoloy 800/800H/800HT wire respond to aging?
No. The family hardens only through cold work, so the temper you order is the state this Incoloy 800/800H/800HT wire arrives in.
How is the price of this Incoloy 800/800H/800HT wire calculated?
Pricing follows weight for this Incoloy 800/800H/800HT wire, with the prevailing nickel and chromium quotations applied on the order date.
What is your MOQ for this Incoloy 800/800H/800HT wire?
One spool covers many common diameters of this Incoloy 800/800H/800HT wire.
What are your trade terms for this Incoloy 800/800H/800HT wire?
FOB covers most orders for this Incoloy 800/800H/800HT wire, and EXW or CIF terms are available when you ask.
What is the lead time for this Incoloy 800/800H/800HT wire?
Stock sizes of this Incoloy 800/800H/800HT wire dispatch in 7 to 15 days, while custom drawing takes longer.
Do you provide EN 10204 3.1 or 3.2 certificates for this Incoloy 800/800H/800HT wire?
Yes. Every coil of this Incoloy 800/800H/800HT wire ships with 3.1, and a 3.2 endorsement is booked through the order.
What information should an enquiry for this Incoloy 800/800H/800HT wire include?
Please send the diameter, temper, coil weight, standard and destination so we can quote this Incoloy 800/800H/800HT wire accurately.
REQUEST FOR QUOTATION
Need A Custom Alloy Solution?
Incoloy 800/800H/800HT wire is quoted by diameter, temper and coil weight to BS 3075 NA15. Send those figures with your quantity so we can price this 800 series wire.
Specifically, we review your Incoloy 800/800H/800HT wire specification, confirm the designation and document scope, and return pricing with clear terms. Production then follows the signed specification, and each consignment of this Incoloy 800/800H/800HT wire ships with the full paperwork set.
