01
Hastelloy C-22 Bright-Drawn Bar
Drawn bar pairing a smooth skin with close size control.
Request Availability →Hastelloy C-22 Bright Bar
Hastelloy C-22 bright bar to ASTM B574 with clean finishes for lathes producing oxidising-acid and pharmaceutical parts.
One Scope Table, One Grade
ASTM B574 carries a family of low-carbon grades, and every heat of this Hastelloy C-22 bright bar reads N06022.
Hardness Records for Sour Duty
Moreover, NACE MR0175 orders for this Hastelloy C-22 bright bar carry hardness data keyed to each lot.
Anneal Step on the Record
Furthermore, the release papers name the 1121 °C anneal and water quench behind this Hastelloy C-22 bright bar.
PRODUCT OVERVIEW
About Hastelloy C-22 Bright Bar
Hastelloy C-22 bright bar arrives in UNS N06022, the nickel-chromium-molybdenum-tungsten grade that holds nitric acid, ferric chloride and wet chlorine at bay. Cupric chloride etch baths, chlorine dioxide bleach liquor and chloride-bearing flue gas also sit inside the envelope of this bright bar.
Bright bar comes off B574 stock, and we name the finish route on the offer instead of assuming it. Each order for this Hastelloy C-22 bright bar ships with heat-number records, a solution-anneal record and EN 10204 3.1 paperwork for goods-in checks. Besides, we agree the anneal record and the finish on the bright bar before we book a heat of UNS N06022.
Meanwhile, the Hastelloy C-22 material page holds the chemistry and the sour-service data behind this Hastelloy C-22 bright bar for cross-reference.
PRODUCT FEATURES
Key Features of Hastelloy C-22 Bright Bar
Hastelloy C-22 bright bar arrives in UNS N06022, the chromium-rich nickel-chromium-molybdenum-tungsten grade whose chromium above 20% carries nitric acid and wet chlorine while molybdenum and tungsten hold reducing acids in check. We supply ASTM B574 bright bar in bright-drawn, peeled and ground finishes for pharmaceutical reactors, pickling lines and flue-gas desulfurisation hardware. Every Hastelloy C-22 bright bar consignment travels with heat-number traceability, EN 10204 3.1 mill test reports and full export documentation.
Hastelloy C-22
Nitric Acid Resistance
For example, chromium above 20% in this Hastelloy C-22 bright bar holds nitric acid duty that a lower-chromium grade cannot take.
01
Ferric and Cupric Chloride Duty
Specifically, oxidising chloride salts leave this Hastelloy C-22 bright bar unaffected on wetted surfaces.
02
Wet Chlorine Capability
Moreover, this Hastelloy C-22 bright bar serves moist chlorine and chlorine dioxide streams without a lining.
03
NACE MR0175 Qualification
Besides, sour-service release for this Hastelloy C-22 bright bar follows NACE MR0175 / ISO 15156 with hardness recorded per lot.
04
Ultra-Low Carbon Weld Zones
In addition, carbon at 0.015% max and silicon at 0.08% max leave no carbides in this Hastelloy C-22 bright bar to precipitate.
05
Pitting Resistance Near 70
Therefore, a pitting resistance equivalent number close to 70 keeps chloride attack off this Hastelloy C-22 bright bar.
06
Cold-Work Strength
Consequently, drawing raises the proof stress of this Hastelloy C-22 bright bar above the annealed floor where shafts need it.
07
Non-Magnetic Behaviour
Finally, instrument assemblies sit comfortably with this Hastelloy C-22 bright bar because the grade stays practically non-magnetic at ambient temperature.
08
WHY CHOOSE US
Why Choose Hastelloy C-22
Lathe-fed pharmaceutical parts make finish the deciding factor in Hastelloy C-22 bright bar. Specifically, we fix the drawing, peeling or grinding route for this Hastelloy C-22 bright bar before quoting.
01
Duty Read Before Pricing
We record the medium, its concentration and its temperature for your Hastelloy C-22 bright bar before proposing a delivery state.
02
Certificates Tied to the Heat
Specifically, EN 10204 3.1 papers, heat numbers and hardness records follow each Hastelloy C-22 bright bar consignment.
03
Trial Pieces and Container Lots
In addition, this Hastelloy C-22 bright bar flows through one route whether you order a single length or a container lot.
04
Terms Stated in Writing
Quotations for this Hastelloy C-22 bright bar name the medium, section, finish and document set rather than leaving them open.
MANUFACTURING PROCESS
Reliable Production For Critical Applications
Bar production for Hastelloy C-22 bright bar runs from charge weighing to final packing. Our team logs each stage of this Hastelloy C-22 bright bar route against its heat number.
01
Charge Weighing
We take electrolytic nickel, chromium, molybdenum and tungsten as the charge for this Hastelloy C-22 bright bar and verify the analysis.
02
Melting and Refining
First, the charge for this Hastelloy C-22 bright bar melts and refines under AOD practice that holds carbon low.
03
Hot Reduction
Next, forging and rolling reduce the ingot to this Hastelloy C-22 bright bar section.
04
Solution Annealing
Then, we hold this Hastelloy C-22 bright bar at 1121 °C and quench it in water.
05
Pickling and Descale
After that, acid pickling leaves this Hastelloy C-22 bright bar scale-free for fabrication.
06
Cold Finishing
We then draw, turn or grind this Hastelloy C-22 bright bar to the ordered size and finish.
07
Straightening
Subsequently, straightening brings this Hastelloy C-22 bright bar inside the ordered runout band.
08
Testing and Release
Finally, chemistry, hardness and dimensional checks clear this Hastelloy C-22 bright bar for dispatch.
Manufacturing Facility
MANUFACTURING CAPABILITY
Advanced Production For Nickel Alloy Products
Holdings and made-to-order lots of Hastelloy C-22 bright bar leave on a single schedule. Moreover, this Hastelloy C-22 bright bar belongs to our bar and rod program.
20,000+ m²
Factory Area
Hot working, annealing, drawing and pickling lines for Hastelloy C-22 bright bar share one site.
50+
Production Machines
Units covering hot working, annealing, drawing and pickling for this Hastelloy C-22 bright bar.
600 Tons
Monthly Capacity
Hastelloy C-22 bright bar output across stock and bespoke lots.
30+
Technical Engineers
Metallurgists who set the anneal plan and hardness scope of this Hastelloy C-22 bright bar against your duty.
30+ Countries
Export Reach
In addition, sealed export packing carries this Hastelloy C-22 bright bar to buyers on five continents.
QUALITY ASSURANCE
Strict Quality Control From Production To Delivery
No Hastelloy C-22 bright bar leaves the yard before its heat has cleared our ISO 9001 inspection route. In addition, we check this Hastelloy C-22 bright bar against the chemistry, hardness, dimensions and surface the order names.
01
Heat Identification
We confirm the grade and heat number of this Hastelloy C-22 bright bar against your purchase order.
02
Hardness Verification
Specifically, sour-service lots of this Hastelloy C-22 bright bar go against the 35 HRC ceiling per NACE MR0175.
03
Dimensional Verification
In addition, the diameter, length and runout of this Hastelloy C-22 bright bar go against the ordered tolerance class.
04
Certificate Assembly
Every consignment of this Hastelloy C-22 bright bar ships with EN 10204 3.1 papers keyed to its heat.
PRODUCT FORMS
Available Product Forms
Conditions and variants of Hastelloy C-22 bright bar cover different machining and service needs. In addition, the list below sets out the Hastelloy C-22 Bright Bar variants we quote most often.
02
Hastelloy C-22 Peeled Bar
Peeled bar carrying a machined skin and an even diameter.
Request Availability →
03
Hastelloy C-22 Centreless-Ground Bar
Ground bar held to a close diameter and straightness band.
Request Availability →
04
Hastelloy C-22 Precision-Ground Bar
Precision-ground bar for tight-tolerance pharmaceutical components.
Request Availability →
05
Hastelloy C-22 Polished Bar
Polished bar for parts that want reduced surface roughness.
Request Availability →
06
Hastelloy C-22 Custom Bright Bar
Bright stock finished against your surface and tolerance callout.
Request Availability →
APPLICATIONS
Engineered For Demanding Industries
Hastelloy C-22 bright bar suits duty where nitric acid, ferric chloride and chloride cracking meet one component. In addition, the applications below show where this Hastelloy C-22 bright bar serves.
Discuss Your Application →
01
Hastelloy C-22 Lathe-Fed Pharmaceutical Parts
Stock feeding sliding-head and turret lathes on API contracts.
02
Hastelloy C-22 Nitric Acid Instrument Fittings
Fittings and adaptors serving nitric acid instruments.
03
Hastelloy C-22 Ferric Chloride Sampling Probes
Probe bodies machined from bright stock for etch liquor.
04
Hastelloy C-22 Scrubber Thermowell Bar Stock
Bar drilled and finished into thermowell bodies for absorber towers.
05
Hastelloy C-22 Precision Plungers for Etch Dosing
Plungers held to tight bore and diameter limits.
06
Hastelloy C-22 Cupric Chloride Valve Trim
Trim parts machined for cupric chloride control valves.
07
Hastelloy C-22 Mixed-Acid Pump Sleeves
Sleeves turned from bright stock for mixed-acid pump assemblies.
08
Hastelloy C-22 Custom Bright Components
Bespoke parts produced to your drawing from bright stock.
TECHNICAL INFORMATION
Technical Specifications
Detailed technical information including chemical composition, mechanical properties, standards and available dimensions.
Chemical Composition
ASTM B574 sets chromium between 20.0% and 22.5% in this bright bar, roughly six points above the C-276 window, while molybdenum at 12.5–14.5% and tungsten at 2.5–3.5% carry the reducing side of the same duty. Besides, carbon at 0.015% maximum and silicon at 0.08% maximum keep carbides out of the grain boundaries of this bright bar, so a welded joint holds its corrosion resistance without a post-weld anneal.
For the full element-by-element limits behind this bright bar, open the composition breakdown recorded on the Hastelloy C-22 material page.
Mechanical Properties
Minimum room-temperature values below come from the rod and bar table of ASTM B574 for UNS N06022. Consequently, the ordered state and the hardness basis govern final acceptance of Hastelloy C-22 bright bar.
| Condition and Grade | Tensile Strength, min. | Yield Strength (0.2%), min. | Elongation, min. |
|---|---|---|---|
| Solution Annealed — UNS N06022 | ≥690 MPa (100 ksi) | ≥310 MPa (45 ksi) | 45% |
- ASTM B574 sets one solution-annealed state for rod and bar at these minimums, and its mechanical table runs to three columns with no hardness limit at all. Besides, the as-cold-finished clause of that standard reaches other grades in its scope list rather than N06022, so drawn and ground bar of this grade is agreed at quotation. Therefore, sour-service orders carry a per-lot hardness record measured against the 35 HRC ceiling, and no mill hardness maximum is printed on the release.
Physical Properties
Data sheets put the density of this bright bar near 8.69 g/cm³ and its melting range between 1357 and 1399 °C. Moreover, the pitting resistance equivalent number of this bright bar sits close to 70, which is what keeps chloride pitting off wetted surfaces. Besides, the nickel-rich matrix leaves this bright bar practically non-magnetic at ambient temperature.
Meanwhile, the physical properties table on the Hastelloy C-22 material page carries the modulus, the expansion figure and the remaining design values behind this bright bar.
Heat Treatment
No step matters more to this grade than the water-quenched anneal, because the corrosion resistance the media demand comes back only with a rapid quench straight after 1121 °C. In addition, we supply this Hastelloy C-22 bright bar in whichever state your duty calls for.
| Condition | Typical Treatment |
|---|---|
| Solution Annealed | Held at 1121 °C, then water quenched, because slow cooling would let intermetallic phases form |
| Hot-Worked | Delivered as-rolled or as-forged, with the anneal agreed where the order calls for it |
| Cold-Drawn | Drawn after annealing, with the reduction recorded so the higher proof stress is documented |
| Stress-Relief Warning | A conventional 650 °C relief cycle destroys the corrosion resistance of this grade, so residual-stress work needs a full anneal instead |
| Sour-Service Release | NACE MR0175 orders carry a per-lot hardness record against the 35 HRC ceiling |
Standards
ASTM B574 is the primary rod and bar document for this bright bar, issued by ASTM International, and its scope table carries a family of low-carbon nickel-chromium-molybdenum grades with N06022 among them. Moreover, ASME SB574 takes over wherever equipment falls under pressure-code jurisdiction. Besides, DIN 17752, ISO 9723 and VdTÜV Werkstoffblatt 479 serve the European and international routes.
| Standard | Product or Application |
|---|---|
| ASTM B574 / ASME SB574 | Nickel-chromium-molybdenum-tungsten rod and bar, UNS N06022 in the scope table |
| DIN 17752 / ISO 9723 | German and international bar documents |
| VdTÜV 479 / NACE MR0175 | German material sheet and sour-service qualification |
Finally, the full standards list that the Hastelloy C-22 material page holds adds the pressure documents, the European designations and the other product documents behind this bright bar.
Dimensions
Dimensions of Hastelloy C-22 bright bar follow the route, the document and the order quantity. Therefore, typical supply ranges sit in the table below, so please confirm your sizes in the inquiry.
| Product Form | Typical Supply | Length |
|---|---|---|
| Bright Bar | 6–150 mm dia. | Cut to length or random |
| Bright-Drawn Bar | 6–80 mm dia. | Cut to length |
| Peeled Bar | 20–100 mm dia. | Cut to length |
| Centreless-Ground Bar | 3–100 mm dia. | Cut to length |
| Precision-Ground Bar | 3–80 mm dia. | Cut to length |
| Polished Bar | 6–100 mm dia. | Cut to length |
| Custom Bright Bar | To drawing | Custom |
Available sizes of this Hastelloy C-22 bright bar depend on the route, the document, the state and the lot size. Please confirm the size, section and length you need for this bright bar in the inquiry.
Surface Finishes
Surface condition decides how this bright bar performs in nitric acid trains, ferric chloride pickling lines and pharmaceutical reactors, and most stock leaves our yard solution annealed and pickled so it arrives ready for oxidising duty. Specifically, we settle the finish on this Hastelloy C-22 bright bar before the order leaves the desk.
| Surface Condition | Typical Use |
|---|---|
| Cold Drawn | Drawn stock giving this bright bar close diameter control and a smooth bright skin. |
| Bright Annealed | Protective-atmosphere annealing leaves this bright bar oxide-free and ready to redraw. |
| Polished | Reduced roughness on this bright bar for pharmaceutical contact and visible components. |
Meanwhile, the surface finishes table recorded on the Hastelloy C-22 material page lists the remaining conditions quoted for this bright bar.
Related forms from the same heat cover Hastelloy C-22 Centreless-Ground Rod, Hastelloy C-22 Cold-Drawn Bar and Hastelloy C-22 Flat Bar when your bright bar order needs them.
TECHNICAL DOCUMENTATION
Download Technical Datasheet
Get detailed information including specifications, standards, dimensions and material properties.
HOW TO START
Start Your Order in 6 Simple Steps
A single coordinator carries your Hastelloy C-22 bright bar order from the first question through to loading. Therefore, most orders for this Hastelloy C-22 bright bar travel from quotation to dispatch inside three weeks.
1
Send the Medium Data
Give us the medium, its concentration and its temperature, plus the size, quantity and standard this Hastelloy C-22 bright bar will face.
2
Fix the State
Then we set the annealing step, the hardness basis and the tolerance band for this Hastelloy C-22 bright bar.
3
Review the Offer
Pricing for this Hastelloy C-22 bright bar arrives by size, quantity and destination port.
4
Approve the Order
You confirm the specification, the terms and the schedule of this Hastelloy C-22 bright bar in writing.
5
Witness Points Agreed
Any third-party inspection or hardness review of this Hastelloy C-22 bright bar is booked before production starts.
6
Dispatch and Documents
This Hastelloy C-22 bright bar arrives with mill papers, a packing list and the certificate set.
CERTIFICATIONS & QUALITY DOCUMENTATION
Certifications & Quality Documentation
Our production and inspection processes are certified to international standards, and every delivery ships with EN 10204 3.1 mill test certificates.
ISO 9001:2015
Quality Management System
PED 2014/68/EU
Pressure Equipment Directive
ASTM / ASME
Material Standards Compliance
EN 10204 3.1
Mill Test Certificates
FAQ
Frequently Asked Questions
Which standard covers this Hastelloy C-22 bright bar?
ASTM B574 and ASME SB574 govern this Hastelloy C-22 bright bar, and the B574 scope carries a family of low-carbon grades with N06022 among them.
Is this Hastelloy C-22 bright bar suitable for nitric acid duty?
Yes. Chromium above 20% gives this Hastelloy C-22 bright bar its resistance to nitric acid, ferric chloride and cupric chloride.
Does this Hastelloy C-22 bright bar qualify for sour service?
Yes. We release this Hastelloy C-22 bright bar to NACE MR0175 / ISO 15156, and hardness is recorded per lot against the 35 HRC ceiling.
Which anneal does this Hastelloy C-22 bright bar receive?
We hold this Hastelloy C-22 bright bar at 1121 °C before a water quench, and the release papers record that step for your lot.
How is the price of this Hastelloy C-22 bright bar calculated?
Weight in kilograms drives pricing for this Hastelloy C-22 bright bar, with the nickel, chromium and molybdenum quotations fixed on the date you receive the offer.
What is your MOQ for this Hastelloy C-22 bright bar?
A single bar covers many common sizes of this Hastelloy C-22 bright bar, so trial lengths are welcome before container orders.
What are your trade terms for this Hastelloy C-22 bright bar?
We quote FOB as standard for this Hastelloy C-22 bright bar, and EXW, CIF or DAP terms follow once the destination is fixed.
What is the lead time for this Hastelloy C-22 bright bar?
Expect 7 to 15 days for stock sizes of this Hastelloy C-22 bright bar, while made-to-order annealed heats need about 25 days.
Do you provide EN 10204 3.1 or 3.2 certificates for this Hastelloy C-22 bright bar?
Every heat of this Hastelloy C-22 bright bar ships with EN 10204 3.1, and a 3.2 endorsement is booked through the order.
What should I include in an enquiry for this Hastelloy C-22 bright bar?
Please send the medium, its concentration, its temperature, the section, quantity and destination so we can quote this Hastelloy C-22 bright bar accurately.
REQUEST FOR QUOTATION
Need A Custom Alloy Solution?
We quote Hastelloy C-22 bright bar by finish route, diameter and tolerance to ASTM B574. Send the finish you need and the quantity to price this Hastelloy C-22 bright bar.
We walk through your Hastelloy C-22 bright bar specification, settle the hardness basis and the document scope, then return pricing with clear terms. Production follows the signed specification, and every consignment of this Hastelloy C-22 bright bar leaves with the complete paper set.
